Compatibility · Oct 2026
Goldring 1042 on the Pro-Ject RPM 5 Carbon: does it fit?
Checked on paper: the tonearm of the Pro-Ject RPM 5 Carbon (Pro-Ject 9 EVO Carbon, 8 g effective mass) with the cartridge Goldring 1042 (6.3 g). The Advisor arrives at 12.9 Hz; the verdict is “borderline”. Orientation only; check the manufacturer’s specifications; errors excepted.
Verdict: borderline
Borderline: at least one point is at the edge. Checks at the edge: Resonance.
- Resonance: 12.9 Hz
- Moving mass: 15.3 g
- Compliance: 10 µm/mN at 10 Hz
- Cartridge: 6.3 g
The Goldring 1042 (6.3 g) is a moving-magnet cartridge with 6.5 mV output. Its compliance of 10 µm/mN applies directly at 10 Hz, so the resonance of about 12.9 Hz is not an approximation but lies above the 12 Hz target zone. On the 8 g arm of the RPM 5 Carbon the cartridge is therefore too stiff; it stays at “borderline” because the 14 Hz warning limit is not reached.
The calculation in detail
The check runs in three steps: does the cartridge physically fit the arm, does the resonance of arm and cartridge lie in the target zone, and can the counterweight balance the cartridge weight? The weakest point decides the overall verdict.
-
Mountingfits
The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.
Advisor output: Fixed headshell with half-inch mounting holes (manufacturer: cartridges with a half-inch mount fit).
-
Resonanceborderline
The resonance of 12.9 Hz is above the target zone. The higher it rises, the closer it gets to audible bass; up to 14 Hz this counts as a warning, not as an exclusion.
Advisor output: fᵣ ≈ 12.9 Hz by 159 / √(15.3 × 10); target 8–12 Hz, warning outside 7–14 Hz. Mass 8 g arm + 6.3 g cartridge + 1 g screws = 15.3 g; compliance 10 µm/mN (10 Hz, per data sheet). Calculation note, not a measurement.
-
Counterweightfits
The arm’s counterweight covers the cartridge: 6.3 g lies within the range 5–14 g.
Advisor output: Cartridge 6.3 g is within the range 5–14 g (cartridge weight (Pro-Ject: four counterweights supplied, 5–7.5 / 7–10 / 9–11 / 10–14 g)).
How the resonance comes about
- Moving mass: 8 g arm + 6.3 g cartridge + 1 g screws = 15.3 g.
- Compliance at 10 Hz: The compliance of 10 µm/mN is specified at 10 Hz and is used unchanged.
- Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(15.3 × 10) = 159 / √153 ≈ 12.9 Hz.
The input data
Tonearm: Pro-Ject 9 EVO Carbon (Pro-Ject RPM 5 Carbon)
- Effective mass
- 8 g · manufacturer figure, source: project-audio.com
- Mounting
- fixed headshell with half-inch mount
- Counterweight
- 5–14 g · cartridge weight (Pro-Ject: four counterweights supplied, 5–7.5 / 7–10 / 9–11 / 10–14 g)
Cartridge: Goldring 1042
- Type
- MM · Nude Gyger S line contact
- Weight
- 6.3 g
- Compliance
- 10 µm/mN at 10 Hz
- Tracking force
- 1.5–2.0 g · recommended 1.7 g
- Output voltage
- 6.5 mV
- Market price
- about €380–450 (prices without guarantee, Oct 2026)
In our data there is no fixed factory cartridge documented for the Pro-Ject RPM 5 Carbon (manufacturer: available with or without an Ortofon 2M Silver (MM)). The calculation applies to a cartridge of your own choice.
What you can do with this
- Check the highlighted points above (Resonance) in the manufacturer’s documents.
- If needed, ask a dealer or the manufacturer whether the combination is recommended in everyday use.
- If you are unsure, look for a cartridge that passes all three checks (see the alternatives below).
The Goldring 1042 is a moving-magnet cartridge (6.5 mV) and works on a normal MM phono input. If the Pro-Ject RPM 5 Carbon has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
Alternatives
Our tip: The Sumiko Moonstone (about €300–390) is suspended more softly and calculates to 8.7 Hz at 6.6 g.
More cartridges on the Pro-Ject RPM 5 Carbon
On the Pro-Ject RPM 5 Carbon these cartridges also pass all three checks, at a similar price (without guarantee):
- Nagaoka MP-200: calculated resonance 11.2 Hz, 6.5 g, about €400–480
- Audio-Technica AT-OC9XEN: calculated resonance 9.7 Hz, 7.6 g, about €280–370
- Ortofon Quintet Blue: calculated resonance 9.7 Hz, 9 g, about €480–550
- Sumiko Moonstone: calculated resonance 8.7 Hz, 6.6 g, about €300–390
The Goldring 1042 on other turntables
On paper the Goldring 1042 can also be run on these turntables without objection:
- Pro-Ject Signature 12: calculated resonance 9.5 Hz, arm 20.6 g
Method in brief
- Procedure
- Same formula as in the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
- Verdict rule
- One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
- Data
- Advisor data of 2 Oct 2026, page of 3 Oct 2026
- Limits
- No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.
Frequently asked questions
Is the Goldring 1042 a good choice for the Pro-Ject RPM 5 Carbon?
With reservations. The Goldring 1042 on the Pro-Ject RPM 5 Carbon is borderline; Resonance is at the edge of the target zone. Calculated resonance: 12.9 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.
At what frequency do the Goldring 1042 and the arm of the Pro-Ject RPM 5 Carbon resonate?
About 12.9 Hz. The calculation uses 159 / √(mass × compliance): 15.3 g moving mass (arm 8 g, cartridge 6.3 g, screws 1 g) and 10 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.
Is the counterweight of the Pro-Ject RPM 5 Carbon sufficient for the Goldring 1042?
The arm’s counterweight covers the cartridge: 6.3 g lies within the range 5–14 g.
What phono input does the Goldring 1042 need?
The Goldring 1042 is a moving-magnet cartridge (6.5 mV) and works on a normal MM phono input. If the Pro-Ject RPM 5 Carbon has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
How reliable is this calculation?
It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet. Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.
Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability
Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026