Before you invest in a new component, it is worth looking at measures that cost little or nothing. Not every one of them changes the sound much. For each point we say honestly what it does, how big the effect realistically is, roughly what it costs and which mistakes are typical. The basis is manufacturer information and international trade press, no listening tests or measurements of our own. Prices are rough price bands, Oct 2026, without guarantee.
Speaker placement€0
What it does: The distance to the rear wall, the side walls and the listening seat decides how much bass the room adds and how stable the stereo centre is. Close to the wall gives more bass, further into the room usually more precise imaging. Rear-ported bass-reflex speakers are particularly sensitive to wall distance.
Realistic effect: Of all the points here, often the most audible, and it costs nothing. How big the effect is depends on the room, though. A boomy bass often calms down with just a few centimetres more wall distance. Placement cannot work miracles.
Typical mistakes: Putting speakers in a corner (What Hi-Fi? links this to “fat, lumpy” bass). Placing the speakers at unequal distances from the seat. Choosing the toe-in out of habit instead of following the manual, since some models are voiced to fire straight ahead. Running standmounts on a crowded shelf. Putting the speakers on the same piece of furniture as the turntable.
Tip: Start with an equilateral triangle of both speakers and the seat. Then move in small steps and change only one thing at a time.
Sources: What Hi-Fi?: How to set up and position your speakers
Stylus gauge, tracking force & alignment with a protractorprotractor often included or €0–20, gauge approx. €15–90
What it does: Tracking force is the force with which the stylus sits in the groove. The target value is in the cartridge’s data sheet, usually between 1.5 and 2.5 g. With the protractor you align the cartridge so that the cantilever is parallel to the guide lines at two points. That way the stylus plays as evenly as possible from the outer to the inner grooves. Anti-skate compensates for the arm’s pull towards the centre.
Realistic effect: If tracking force is too high, the sound turns thick according to What Hi-Fi? and the groove wears faster. If it is too low, the sound is thin and the stylus jumps more easily. If force and alignment were already right, a gauge changes nothing and only gives certainty. Above all, this step protects stylus and records.
Typical mistakes: Trusting only the scale on the counterweight. Using the “coin trick” shortcuts What Hi-Fi? explicitly warns against. Not measuring at the height of the record surface. Not rechecking after changing a mat or cartridge. Forgetting anti-skate. Tightening the headshell screws before the alignment is right.
Tip: Whether a new cartridge suits your tonearm at all (resonance, mass, counterweight) is worked out in the compatibility hub. Suitable cartridges are in the cartridge top list.
Sources: What Hi-Fi?: 5 mistakes to avoid when setting up your record player · Ortofon: Alignment tool · Ortofon: DS-3 Stylus Pressure Gauge · Ortofon: FAQ
Stylus cleaning (brush, fluid, gel)stylus brush approx. €5–20, cleaning fluid approx. €10–20
What it does: Dust and residue from the groove collect on the stylus. Ortofon and Audio-Technica agree: brush only from back to front, from the cartridge towards the tip, never sideways and never backwards. Ortofon explicitly recommends a dry brush only, before every record side. Ortofon advises against fluids and gels because they can attack the stylus cement or the cartridge internals. Audio-Technica, by contrast, sells its own ethanol-based fluid, the AT607a.
Realistic effect: A ball of fluff on the stylus causes clearly audible distortion according to What Hi-Fi?. If the stylus is clean, cleaning changes nothing in the sound. Regular cleaning does protect stylus and records, but it does not replace a worn stylus.
Typical mistakes: Brushing sideways or front to back, which can bend the cantilever. Using fluid or gel on a cartridge whose maker advises against it; with Ortofon it can void the warranty. Letting fluid drip. Fitting or transporting the cartridge without the stylus guard.
Tip: Follow the care instructions of your cartridge’s maker, as the brands contradict each other. How stylus shapes differ and when a replacement is due is in the stylus shapes guide.
Sources: Ortofon: Protect your equipment · Ortofon: Stylus care · Audio-Technica: How to clean a stylus · What Hi-Fi?: How to clean vinyl records
Record cleaning (brush, wet cleaning, machine)carbon brush approx. €10–25, simple wet washers approx. €40–100, cleaning machines from a few hundred euros
What it does: The carbon or microfibre brush picks up surface dust before playing. Hold it lightly on the spinning record and wipe the line of dust off sideways. Dirt in the groove, such as finger grease or old residue, only comes off with wet cleaning. For that, Ortofon names lukewarm demineralised water with a dash of sulphonic soap and advises against solvents. The next step is a cleaning machine, which applies fluid and vacuums it off together with the dirt. According to What Hi-Fi?, such machines start at a few hundred pounds.
Realistic effect: With dirty second-hand records the effect is often clear and the crackle drops. With new or well-kept records it is small. No cleaning repairs scratches or worn grooves. Clean records also spare the stylus.
Typical mistakes: Touching the grooves with your fingers. Using alcohol or solvents. Putting the record back in its sleeve while still wet. Putting a freshly cleaned record into the old, dusty inner sleeve. Pressing the brush down so it only pushes the dust around.
Tip: A machine mainly pays off with a large collection or many second-hand records. As an alternative, What Hi-Fi? mentions a cleaning service for a small fee per record.
Sources: What Hi-Fi?: How to clean vinyl records · Ortofon: Stylus care · Ortofon: FAQ
Platter mats (felt, cork, leather, rubber/silicone, acrylic)felt approx. €10–30, cork/leather/cork-rubber approx. €20–60, acrylic approx. €50–200
What it does: The mat couples the record to the platter and damps resonances.
Felt gives an even contact according to Pro-Ject, but builds up static, collects dust and damps little, especially on metal platters. Rega, by contrast, deliberately uses a thin wool felt mat, because records are not completely flat and need support without a springy effect.
Cork and leather damp better than felt according to Pro-Ject and keep dust and static away more. Cork-rubber blends come in 1 and 3 mm, the thick version for thin metal platters.
Thick rubber mats can overdamp according to Pro-Ject and leave static on the record, which causes clicks. Silicone is also a soft elastomer. We found no reliable manufacturer statements on the sonic effect of silicone, so we make no claim about it.
Acrylic comes as a mat and as a replacement platter, for example the Pro-Ject Acryl it at 18 mm high. With an acrylic platter the record sits directly on it, without a mat.
Realistic effect: Stereophile names no universally best mat. The result depends on the platter material, on whether the deck is suspended, and on the bearing. A mat usually helps most on a metal platter with thin felt. On a deck voiced for its original mat, such as the Rega models, the benefit is questionable.
Typical mistakes: Ignoring the height. A thicker or thinner mat changes the record height and with it the vertical tracking angle (VTA). The arm then sits lower or higher at the back, and tracking force and arm height need checking again. For Debut and Essential models Pro-Ject even sells a 1.5 mm spacer for the tonearm (VTA it) so that thicker mats fit. Another mistake is stacking two mats or putting a mat on an acrylic platter built for direct contact. Also check that the clamp still grips properly with the mat’s thickness.
Tip: Buy at most one mat, then check arm height and tracking force. Decks with a fixed arm and no VTA adjustment cope best with a mat about as thick as the old one. Suitable decks are in the turntable top list.
Sources: Pro-Ject: Cork it · Pro-Ject: Cork & Rubber it (product info) · Pro-Ject: Acryl it · Pro-Ject: VTA it · The Ear: interview with Roy Gandy (Rega) · Stereophile: Spin Doctor #4, page 2
Record clamp and record weightsimple clamps approx. €20–80, heavy weights considerably more
What it does: Clamps and weights press the record onto the mat or platter. The record then sits better, slight warps flatten and the record’s own vibrations drop. Stereophile distinguishes the two: clamps grip the spindle, often with a lift washer, and deliberately flex the record onto the platter. Weights work only through their mass. Pro-Ject builds its Clamp it, at 120 g, deliberately as a clamp, because heavy weights can raise rumble on low-cost decks with small bearings and can arch the record so that the edge lifts.
Realistic effect: With warped records the effect is often easy to notice. With flat records it is small and judged differently depending on the deck. According to Stereophile, the idea that the record slips without a clamp is a myth.
Typical mistakes: Putting a heavy weight on a deck with a suspended subchassis. Stereophile names Linn as an example, where the extra mass upsets the suspension. Putting a heavy weight on a low-cost deck with a weak bearing or motor. Rega advises against adding mass to the platter of its lightweight decks in general. Clamps do not fit every spindle, as short or fixed spindles exist too. Tightening the clamp too hard, which presses the label into the recess and lifts the edge.
Tip: Check the turntable’s manual first. If it says nothing about clamps or extra weight, or the maker advises against them, leave them off.
Sources: Stereophile: Spin Doctor #4 – Platter Mats, Clamps, Weights · Pro-Ject: Clamp it · SoundStage! Xperience: Rega Research – A History
Placement, equipment feet and isolationspirit level approx. €5–15, equipment feet approx. €20–150, wall shelf approx. €100–250
What it does: The turntable must be level, which you check with a spirit level on the platter. It belongs on a stable support with as little resonance as possible and not next to the speakers (What Hi-Fi?). A wall shelf decouples it from the floor, and Rega sells its own brackets for this. That mainly helps on springy wooden floors, where footsteps make the stylus jump. Roy Gandy of Rega advises a rigid rather than a yielding support. In his view, most vibration arrives through the air.
Realistic effect: If the stylus jumps with footsteps or there is hum and boom at high volume from acoustic feedback, the effect is large. If the turntable already stands stable and far from the speakers, feet and platforms do little at most.
Typical mistakes: Turntable and speakers stand on the same furniture. Putting the turntable on wobbly, hollow furniture. Putting soft damping feet under a deck that already has its own suspension. Keeping the lid closed while listening, although What Hi-Fi? describes it as a catcher for airborne and structure-borne vibration. Mounting the wall shelf on a lightweight partition wall.
Tip: Level and reposition first, which costs nothing. Buy something only if a specific problem remains.
Sources: What Hi-Fi?: 5 mistakes to avoid when setting up your record player · What Hi-Fi?: How to clean vinyl records · The Ear: interview with Roy Gandy (Rega) · Rega: Wall Bracket
Cables – an honest looksolid 2.5 mm² speaker cable approx. €2–6 per metre
What it does: A speaker cable should carry the signal without significant losses. What matters is cross-section, length and clean contacts. DALI recommends at least 2.5 mm² for runs up to 5 m and 4 mm² for longer runs. Both channels should be the same length, and you loop excess cable loosely rather than in tight coils. Terminated ends protect the strands from oxidation. Even thicker cable brings no benefit according to DALI.
Realistic effect: Replacing thin bell-wire cables or oxidised ends can be audible; according to DALI, cable that is too thin makes the bass looser and less defined. Between solid cables of the same cross-section we find no evidence of an audible difference and make no sound promise. The trade press does not agree here: What Hi-Fi? suggests budgeting 10–15% of the system price for cables. DALI advises trusting your own ears rather than the marketing.
Typical mistakes: Buying expensive cables before placement and alignment are right. Using different lengths for left and right. Ignoring loose or oxidised terminals. Leaving a tightly wound reel of cable behind the speaker.
Tip: Prices per metre and cross-sections of solid cables are in the speaker cable top list.
Sources: DALI: Does speaker wire matter? · What Hi-Fi?: How to set up and position your speakers
The budget levels follow. The €100 level starts right here: align first, then the stylus.