Compatibility · Oct 2026

Ortofon 2M Bronze on the Rega Planar 3: does it fit?

Does the Ortofon 2M Bronze fit the tonearm of the Rega Planar 3? With 11 g of effective arm mass and 7.2 g for the cartridge the calculation gives 7.7 Hz; verdict: not verifiable. Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: not verifiable Resonance 7.7 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: not verifiable

Not verifiable: key data is missing. Checks at the edge: Resonance; open: Mounting, Counterweight.

  • Resonance: 7.7 Hz
  • Moving mass: 19.2 g
  • Compliance: 22 µm/mN at 10 Hz
  • Cartridge: 7.2 g

The 2M Bronze is suspended more softly than the 2M Red (22 instead of 20 µm/mN) and weighs the same. On the 11 g RB330 that pushes the resonance below the 8 Hz of the target zone, though still above the warning limit of 7 Hz. That is not a knock-out criterion, but it is a reason to keep an eye on this point. Together with the two open items for the Rega arm the result is “not verifiable”.

Resonance band: Ortofon 2M Bronze on Rega Planar 3 Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 7.7 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 7.7 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz).

The calculation in detail

Whether arm and cartridge work together depends on mounting, resonance and counterweight. Each point is rated on its own, and the verdict follows the worst result.

  • Mountingnot verifiable

    Rega names neither the half-inch standard nor an adapter for the arm. According to Rega’s accessory page third-party cartridges can be mounted, but an explicit assurance for half-inch cartridges is missing.

    Advisor output: Rega arm (3-point mounting): Rega names neither the half-inch standard nor an adapter; third-party cartridges can be mounted according to Rega’s accessory page (height: possibly a 2 mm spacer), an adapter is not documented. Counterweight weight range n/a – not verifiable.

  • Resonanceborderline

    The resonance of 7.7 Hz is below the target zone. Low resonances react more strongly to warped records and footfall; below 7 Hz this counts as a warning, not as an exclusion.

    Advisor output: fᵣ ≈ 7.7 Hz by 159 / √(19.2 × 22); target 8–12 Hz, warning outside 7–14 Hz. Mass 11 g arm + 7.2 g cartridge + 1 g screws = 19.2 g; compliance 22 µm/mN (10 Hz, per data sheet). Calculation note, not a measurement.

  • Counterweightnot verifiable

    No weight range is documented for this arm’s counterweight; the cartridge weighs 7.2 g.

    Advisor output: Weight range of the arm not documented (n/a) – check the manufacturer’s specification (cartridge 7.2 g).

How the resonance comes about

  1. Moving mass: 11 g arm + 7.2 g cartridge + 1 g screws = 19.2 g.
  2. Compliance at 10 Hz: The compliance of 22 µm/mN is specified at 10 Hz and is used unchanged.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(19.2 × 22) = 159 / √422.4 ≈ 7.7 Hz.

The input data

Tonearm: Rega RB330 (Rega Planar 3)

Effective mass
11 g · manufacturer figure, source: rega.co.uk
Mounting
Rega three-point mounting (half-inch not explicitly documented)
Counterweight
not documented

Cartridge: Ortofon 2M Bronze

Type
MM · Nude Fine Line r/R 8/40 µm · alloy cantilever
Weight
7.2 g
Compliance
22 µm/mN at 10 Hz
Tracking force
1.4–1.7 g · recommended 1.5 g
Output voltage
5 mV
Market price
about €350–420 (prices without guarantee, Oct 2026)

In our data there is no fixed factory cartridge documented for the Rega Planar 3 (manufacturer: optional from the factory: Rega Nd3 or Nd5 (MM); base unit without cartridge). The calculation applies to a cartridge of your own choice.

Next steps

  • Ask the manufacturer or a dealer about: Mounting, Counterweight (see the Advisor output above).
  • The resonance alone can be calculated: 7.7 Hz (see above).
  • Without a weight range and a mounting statement we say neither “fits” nor “does not fit”.

The Ortofon 2M Bronze is a moving-magnet cartridge (5 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: With only 6 g of arm mass the Pro-Ject Debut Carbon EVO moves the same cartridge to 9 Hz and thus into the target zone; all three checks are documented there.

The Ortofon 2M Bronze on other turntables

If you would rather change the turntable: on these models the Ortofon 2M Bronze passes all three checks:

Method in brief

Procedure
Following the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Can I run the Ortofon 2M Bronze on the Rega Planar 3?

The available manufacturer data does not allow a final answer. Open: Mounting, Counterweight. Calculated resonance: 7.7 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.

What resonance frequency results for the Ortofon 2M Bronze on the Rega Planar 3?

About 7.7 Hz. The calculation uses 159 / √(mass × compliance): 19.2 g moving mass (arm 11 g, cartridge 7.2 g, screws 1 g) and 22 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the Rega Planar 3 sufficient for the Ortofon 2M Bronze?

No weight range is documented for this arm’s counterweight; the cartridge weighs 7.2 g. Check the manufacturer’s specification before buying.

What phono input does the Ortofon 2M Bronze need?

The Ortofon 2M Bronze is a moving-magnet cartridge (5 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet. Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026