Guide · Oct 2026
Stylus shapes explained: which profile suits your cartridge?
The stylus shape helps decide how finely a cartridge traces the groove, how precisely you must align it and how long the stylus lasts. We compare nine shape families from spherical to Replicant 100 with radii and life figures from manufacturer data and show matching cartridges for each shape from the cartridge top list. Prices as a price band, without guarantee.
Stylus shapes in 60 seconds
- Spherical (conical): one round radius of typically 0.6 mil, robust, affordable, forgiving to align – but less precise in the treble, especially towards the centre of the record.[1][24]
- Elliptical: two radii, narrow in the direction of travel; traces high frequencies more accurately and reduces inner-groove distortion. The standard on many entry-level cartridges.[1]
- Line-contact family (Shibata, Fine Line, Line Contact, MicroLine, Micro Ridge, Replicant 100, Gyger): very small side radius, long vertical contact line on the groove wall. More detail and usually longer life, but higher demands on alignment and cleanliness.[1][18][21]
- Stylus life: Audio-Technica gives about 300 to 1,000 hours for its VM styli depending on the shape; Ortofon gives more than 2,000 hours of total life for the Replicant 100 stylus with proper care.[2][9]
- No shape is best for every setup. Soundsmith describes every stylus shape as a compromise between cost, performance and alignment effort.[18]
What a stylus shape is: groove, cutting stylus and two radii
A record groove is a V-shaped trench with an included angle of about 90 degrees; the music sits in the lateral and vertical excursions of its two walls.[23] It is cut with a chisel-shaped cutting stylus whose edges are rounded to only about 2 µm.[21][23] Every playback stylus is therefore a compromise: it should follow a shape left by a sharp-edged tool without damaging the groove itself.
A shape is usually described by two radii. The side radius r (also scanning or tracing radius) measures the tip in the direction of travel; the smaller it is, the finer the excursions the stylus can trace. The contact radius R describes how the tip rests against the walls across the groove. Manufacturers give the figures in µm or in mil; one mil is a thousandth of an inch, i.e. 25.4 µm.[1] Ortofon writes, for example, “r/R 8/18 µm”, Audio-Technica “0.3 × 0.7 mil”.[7][1]
Why the inner groove makes the difference
The record turns at a constant speed. Near the label the stylus covers less distance per revolution than at the edge, so the same frequency is stored over a shorter length. Sumiko does the maths: a 10 kHz tone needs 50.8 µm of groove length per cycle at the outer edge and only 20.32 µm in the inner groove.[19] Hi-Fi News gives about 7 µm for a half-cycle of 15 kHz at a groove radius of 6 cm – a tip with a 12 µm radius can no longer trace such excursions cleanly.[23] This is exactly where the typical inner-groove distortion arises, which shows up first on music with long record sides.
A smaller side radius alone would stress the groove more, because the tracking force is spread over a smaller area. That is why the fine shapes extend the contact zone vertically: narrow in the direction of travel, long along the wall. Orbray, one of the large makers of diamond stylus tips, describes exactly this relationship – a longer contact line lowers the pressure and extends the life of record and stylus.[11]
Spherical (conical) stylus
The spherical shape is the oldest and simplest: the tip is round, typically with a 0.6 mil radius, and touches the groove walls in their middle. Audio-Technica calls it the most affordable and most widespread variant and recommends it for older and simpler turntables, for arms with higher tracking force and for tonearms without azimuth adjustment.[1] The tip sits comparatively high in the groove, and because the contact area is round, the stylus rake angle (SRA) hardly matters.[21][22]
The price for this: a large radius traces short wavelengths less well, and treble reproduction is less accurate, especially in the inner groove.[24][23] Soundsmith also points out that conical styli work with higher pressure per area and therefore wear faster.[18] In DJ use, on the other hand, the spherical shape is common because it stays robust when scratching and back-cueing.[6][24]
Spherical does not automatically mean cheap: the Denon DL-103R, an MC classic in our Expert level, uses a round tip of 16.5 µm at 2.5 ± 0.3 g tracking force according to Denon.[17] Shellac records at 78 rpm need even larger radii: Audio-Technica gives 2.5 mil, Ortofon 65 µm for the 2M 78 stylus.[1][7]
- Radii
- one radius, typically 0.6 mil ≈ 15 µm (Audio-Technica, Goldring E2); Orbray gives 10–20 µm[1][14][11]
- Alignment
- SRA uncritical, also suits arms without azimuth adjustment[22][1]
- Stylus life
- Audio-Technica: about 300–500 hours (VM series)[2]
- Price band
- about €35–470 (3 cartridges in our top list)
Spherical cartridges from our top list
- Starter: Audio-Technica AT-VM95C (rank 11 · Index 43 · about €35–45), Goldring E2 (rank 10 · Index 44 · about €70–100)
- Expert: Denon DL-103R (rank 13 · Index 71 · about €420–470)
We list no spherical cartridge in the Premium and Master levels.
Elliptical stylus
An elliptical shape has two radii: wide where the tip rests on the walls, narrow in the direction of travel. Audio-Technica offers sizes of 0.2, 0.3 and 0.4 × 0.7 mil; the smaller the side radius, the finer the tracing and the less tracking force is needed.[1] According to Audio-Technica, the elliptical shape improves frequency response and lowers distortion, especially in the inner grooves.[1] Ortofon uses r/R 8/18 µm on the 2M Red, 2M Blue and the OM range; Sumiko gives 10 × 18, 8 × 18 and 5 × 18 µm as common dimensions.[7][19]
For alignment: elliptical styli react more sensitively to the rake angle (SRA) than spherical ones[22], and for arms without azimuth adjustment Audio-Technica rather recommends the conical shape.[1] Orbray describes that the smaller contact area leads to higher pressure per area, which can shorten stylus life; Audio-Technica gives about 300 hours for elliptical VM styli.[11][2] Ortofon nevertheless stresses that both spherical and elliptical styli can deliver a pleasant listening experience when well matched.[6]
- Radii
- r 5–10 µm, R 15–20 µm (Orbray); examples 8/18 µm (Ortofon), 0.3 × 0.7 mil (Audio-Technica)[11][7][4]
- Alignment
- medium: set tracking force, azimuth and SRA carefully[22]
- Stylus life
- Audio-Technica: about 300 hours (VM series)[2]
- Price band
- about €45–990 (21 cartridges in our top list)
Elliptical cartridges from our top list
- Starter: Ortofon 2M Red (rank 1 · Index 54 · about €85–100), Audio-Technica AT-VM95E (rank 2 · Index 53 · about €55–70)
- Premium: Ortofon 2M Blue (rank 3 · Index 66 · about €160–200), Nagaoka MP-150 (rank 5 · Index 63 · about €320–380)
- Expert: Audio-Technica AT-OC9XEN (rank 14 · Index 70 · about €280–370), Ortofon Quintet Blue (rank 10 · Index 74 · about €480–550)
With 21 entries, the elliptical shape is the most common in our list; it does not appear in the Master level.
Nude or bonded: how the diamond sits on the cantilever
Besides the shape, construction counts. On a bonded stylus only the diamond tip is glued to a small metal shank; this is cheaper but puts more moving mass at the end of the cantilever. A nude stylus is a whole diamond, lighter, oriented along the crystal grain and, according to Audio-Technica, longer-lasting.[1] Soundsmith names the mass of the steel pin as the drawback of the bonded design.[18] The British stylus maker Expert Stylus has been bonding diamonds to steel shanks since 1967 and today also offers re-tipping of worn cantilevers.[20]
How this shows in price can be seen with two pairs of identical shape: Audio-Technica AT-VM95E (0.3 × 0.7 mil, bonded) and Audio-Technica AT-VM95EN (0.3 × 0.7 mil, nude) sit at about €55–70 and about €100–140; Ortofon 2M Red (8/18 µm, bonded) and Ortofon 2M Blue (8/18 µm, nude) at about €85–100 and about €160–200.[4][7] Of the 24 line-contact-family cartridges in our top list, 20 explicitly state a nude stylus in the data sheet.
Shibata stylus
The Shibata is the ancestor of the modern line-contact shapes. Norio Shibata developed it around 1972 at JVC for the CD-4 quadraphonic record, whose carrier signals reached into the ultrasonic range; Sumiko gives 45 kHz.[19][24][25] According to Audio-Technica, the Shibata has more contact area with the groove and stresses it less.[1] Orbray explains this with the longer contact line: lower pressure, longer life for record and stylus.[11] Wikipedia relates an anecdote from the JVC era: demo records worn out after 500 plays with a spherical stylus at 4.5 g still played cleanly with a Shibata stylus.[24]
Ortofon fits the 2M Black with the same Shibata tip as the MC Cadenza Black, with r/R 6/50 µm, and names lower record and stylus wear as well as lower distortion as benefits.[7][8] Audio-Technica gives 2.7 × 0.26 mil for the AT-VM95SH, about 69 × 6.6 µm.[4] Because the contact zone is so narrow in the direction of travel, the Shibata demands precise alignment of overhang, azimuth and SRA; Sumiko warns that misaligned styli with narrow contact can damage the groove.[19][18][22]
- Radii
- r 5–8 µm, R 35–45 µm (Orbray); 6/50 µm (Ortofon), 2.7 × 0.26 mil (Audio-Technica)[11][7][4]
- Alignment
- high: overhang, azimuth, SRA[19][22]
- Stylus life
- Audio-Technica: about 800 hours (VM series)[2]
- Price band
- about €190–2,999 (6 cartridges in our top list)
Shibata cartridges from our top list
- Premium: Audio-Technica AT-VM95SH (rank 6 · Index 62 · about €190–230)
- Expert: Ortofon 2M Black (rank 5 · Index 78 · about €480–600), Hana SL Mk II (rank 3 · Index 82 · about €850)
- Master: Ortofon Cadenza Black (rank 5 · Index 91 · about €2,790–2,999)
Hana also uses the Shibata in the current SL MK II.[16] The Ortofon 2M Black LVB 250 (Expert, rank 1) combines the Shibata with a boron cantilever.
Fine Line stylus
Fine Line is Ortofon’s name for a shape from the line-contact family.[24] The 2M Bronze and the MC Cadenza Red carry a nude Fine Line tip with r/R 8/40 µm.[7][8] According to Ortofon, the slim profile traces even the highest frequencies, and the larger footprint reduces distortion and record wear.[7] In the Vinyl Engine overview, Fine Line with its 40 µm contact radius counts as a less pronounced line-contact shape than variants above 70 µm.[25]
Soundsmith describes better treble reproduction for fine shapes of this kind, especially in the inner grooves, but also higher demands on azimuth, SRA and clean records.[18] Handy: the styli of the 2M Bronze and 2M Black are interchangeable, as are those of the 2M Red and 2M Blue.[7]
- Radii
- 8/40 µm (Ortofon 2M Bronze, Cadenza Red)[7][8]
- Alignment
- high: azimuth, SRA, clean records[18]
- Stylus life
- no shape-specific hour figure found; Ortofon gives up to 1,000 hours in general with proper care[10]
- Price band
- about €350–1,499 (2 cartridges in our top list)
Fine Line cartridges from our top list
- Premium: Ortofon 2M Bronze (rank 1 · Index 69 · about €350–420)
- Master: Ortofon Cadenza Red (rank 12 · Index 85 · about €1,236–1,499)
Line Contact and Special Line Contact
“Line contact” is both a generic term and a product name. After the Shibata, Wikipedia lists further shapes – Hughes (1975), Ogura (1978), van den Hul (1982) – and brand names such as Hyperelliptical (Shure), Fine Line (Ortofon), Line Contact (Audio-Technica) and Stereohedron (Stanton).[24] Soundsmith lists, for example, van den Hul at 4 × 70 µm and Stereohedron at 7 × 72 µm.[18] According to Stereophile, all share the long, narrow vertical contact zone; if it is set wrong, you hear it.[21]
Audio-Technica calls the Special Line Contact (SLC) the shape with the largest contact area, but points out that it can make more surface noise audible on worn records.[1] The AT-ART9XI carries a nude SLC tip on a solid boron cantilever 0.28 mm in diameter.[5] Nagaoka combines a line-contact tip with a boron cantilever in the MP-500 and gives 1.3–1.8 g tracking force.[15]
- Radii
- depending on the maker r about 4–7 µm, R about 70 µm (Soundsmith overview)[18]
- Alignment
- high: SRA, azimuth, overhang[22][21]
- Stylus life
- Audio-Technica: about 800 hours (SLC)[2]
- Price band
- about €800–3,650 (5 cartridges in our top list)
Line-contact cartridges from our top list
- Expert: Nagaoka MP-500 (rank 4 · Index 79 · about €800–900)
- Master: Audio-Technica AT-ART9XI (rank 11 · Index 85 · about €1,399–1,549), Lyra Kleos (rank 6 · Index 90 · about €3,250–3,400)
MicroLine and Micro Ridge
These shapes take the idea furthest: extremely small side radius, very long contact line. Audio-Technica writes that the MicroLine tip replicates the shape of the cutting stylus, wears evenly and extends the life of record and stylus.[1] For the AT-VM95ML and AT-OC9XML the maker gives 2.2 × 0.12 mil (about 56 × 3 µm) as a nude stylus with square shank; the VM95ML is meant to minimise inner-groove distortion.[4][5]
Micro Ridge is the related shape from Orbray (formerly Namiki): r 2–3 µm, R 70–80 µm. According to Orbray and Dynavector, the contact radius does not change with wear.[11][12] Soundsmith adds a warning: the edges of a true Micro Ridge do not widen, but the stylus can be worn out comparatively suddenly – a look through the microscope beats gut feeling.[18] Dynavector lists the Dynavector DV 20X2A with a nude Micro Ridge tip; Hana uses a Microline shape on boron in the Umami Red.[13][16]
- Radii
- MicroLine 2.2 × 0.12 mil ≈ 56 × 3 µm (Audio-Technica); Micro Ridge r 2–3, R 70–80 µm (Orbray)[4][11]
- Alignment
- very high: SRA, azimuth, overhang and clean records[18][22]
- Stylus life
- Audio-Technica: about 1,000 hours (MicroLine); Micro Ridge: radius stays the same with wear, no hour figure[2][11][12]
- Price band
- MicroLine about €150–3,700 (5 cartridges in our top list); Micro Ridge about €900–1,790 (2 cartridges in our top list)
MicroLine and Micro Ridge cartridges from our top list
- Premium: Audio-Technica AT-VM95ML (rank 4 · Index 65 · about €150–190), Audio-Technica AT-VM740ML (rank 2 · Index 68 · about €280–340)
- Expert: Audio-Technica AT-OC9XML (rank 6 · Index 77 · about €550–600), Dynavector DV 20X2A (rank 2 · Index 82 · about €900–990)
- Master: Hana Umami Red (rank 3 · Index 93 · about €3,500–3,700), Lyra Delos (rank 10 · Index 86 · about €1,700–1,790)
Replicant 100
With the Replicant 100, Ortofon claims the shape closest to the cutting stylus: a thin, light profile with an extraordinarily large contact surface.[9] The data sheet of the MC Cadenza Bronze gives r/R 5/100 µm – the largest contact radius in our comparison.[8] On stylus life Ortofon is unusually specific: with proper care, up to 1,000 hours are possible without loss of performance; after that the stylus shows changes, but its total life is expected to exceed 2,000 hours.[9] Proper care, according to Ortofon, includes cleaning the record with a brush before and after every play.[9]
- Radii
- 5/100 µm (Ortofon Cadenza Bronze)[8]
- Alignment
- very high, like all line-contact shapes[21][22]
- Stylus life
- Ortofon: up to 1,000 hours without loss, over 2,000 hours in total[9]
- Price band
- about €2,300–6,999 (3 cartridges in our top list)
Replicant 100 cartridges from our top list
- Master: Ortofon Cadenza Bronze (rank 9 · Index 87 · about €2,300–2,499), Ortofon MC Windfeld Ti (rank 2 · Index 95 · about €5,200–5,499), Ortofon MC Verismo (rank 1 · Index 97 · about €6,500–6,999)
In our list the Replicant 100 appears only in the Master level.
Special shapes: Gyger and relatives
The Swiss Fritz Gyger developed shapes that are also meant to come as close as possible to the cutting stylus; according to the Vinyl Engine overview, a Gyger shape was used from 1987 in the Ortofon OM40, among others.[25] Ortofon names the “Fritz Gyger 70” in its stylus guide and fits the MC Cadenza Blue with the FG 70 variant at r/R 6/70 µm.[6][8] Soundsmith lists Gyger at 5 × 70 µm.[18]
In our list this shape is represented by the Goldring 1042: a nude natural diamond with Gyger S profile, according to Goldring with a 5 µm (0.2 mil) tracing radius, 1.5–2 g tracking force (1.75 g recommended), a recommended effective tonearm mass of 5–25 g and a replaceable stylus.[14] We found no manufacturer hour figure for Gyger shapes.
- Radii
- 6/70 µm (Ortofon FG 70); 5 µm tracing radius (Goldring 1042)[8][14]
- Alignment
- high, like line contact[21]
- Stylus life
- no manufacturer hour figure found
- Price band
- about €380–450 (1 cartridge in our top list)
Gyger cartridges from our top list
- Premium: Goldring 1042 (rank 8 · Index 59 · about €380–450)
Wear and stylus life: what is documented
Hour figures for stylus life are guide values, not guarantees. Audio-Technica provides the most specific numbers for the VM series: conical about 300–500 hours, elliptical 300, Shibata and Special Line Contact 800, MicroLine 1,000 hours.[2] In a release on upgrading cartridges, Audio-Technica gives 300 to 1,000 hours in general, depending on the stylus type.[3] Ortofon’s FAQ speaks of up to 1,000 hours without loss of quality with proper care; for DJ use the maker expects about 500 hours at most.[10]
Other figures circulate too: Soundsmith reproduces a list with values from the stylus maker JICO that defines life by the rise of distortion at 15 kHz (spherical 150, elliptical 250, Shibata and line contact 400, Micro Ridge 500 hours), but explicitly distances itself from the life statements. Soundsmith itself recommends having a properly aligned stylus checked under the microscope at about 1,000 hours, because record damage typically begins after that.[18] Expert Stylus, for example, offers such a microscope inspection.[20]
Rule of thumbOne hour of listening a day adds up to about 365 hours a year. With an elliptical stylus you therefore reach Audio-Technica’s figure after about a year, with MicroLine after almost three years. To care for the stylus, Ortofon says to brush it from back to front, never sideways, and to avoid solvents.[7]
Alignment: why fine shapes need more care
The narrower the contact zone, the more every deviation matters. With a spherical stylus the angle of the tip to the record (SRA, stylus rake angle) hardly matters; with elliptical and line-contact shapes it must be right.[22] Michael Fremer considers 92 degrees ideal and calculates that one degree of SRA on a 9-inch arm requires a height change of about 4 mm at the pivot.[22] Soundsmith describes that a statically set angle of 94–95 degrees drops to about 92 degrees during play.[18] Ortofon gives 20 degrees for the vertical tracking angle (VTA), matching the cutting angle.[10]
Then there are overhang and offset: Ortofon refers to the Baerwald, Löfgren B and Stevenson geometries.[10] Tangential alignment has only two null points; between and beyond them tracking error arises.[19] According to Stereophile, the differences between shapes grow towards the centre of the record, so that is where alignment decides.[21] Whether a cartridge suits the effective mass of your tonearm at all is calculated for typical pairs in our compatibility hub; the basics of compliance and resonance are in the cartridge top list.
Stylus shapes at Ortofon, Audio-Technica, Goldring, Sumiko, Hana, Nagaoka and Shure
Many makers build stylus-swap families: one cartridge body, several styli with different shapes. This is the cheapest way to try a shape or upgrade later.
- Audio-Technica cartridges and styli: all VM95 models share the same body; Audio-Technica offers six interchangeable AT-VMN95 replacement styli for it, including conical, elliptical bonded and nude, MicroLine and Shibata.[4] MicroLine and Shibata are nude with a square shank, the EN stylus nude with a round shank, C and E bonded.[4]
- Ortofon cartridges: the 2M range steps shape and price from the 2M Red (elliptical bonded) via the 2M Blue (elliptical nude) and 2M Bronze (Fine Line) to the 2M Black (Shibata). The styli of Red and Blue are interchangeable, as are those of Bronze and Black.[7]
- Goldring: from the spherical E2 with a 15 µm radius to the 1042 with Gyger S profile.[14]
- Sumiko: Rainier, Moonstone and Olympia appear in our list with an elliptical shape; Sumiko itself describes elliptical and Shibata shapes in its Cartridge 101 text.[19]
- Hana: Shibata in the SL (also in the current SL MK II) and, according to our list, in the SH; Microline in the Umami Red and Umami Blue.[16]
- Nagaoka: line contact in the MP-500[15]; according to our top list, elliptical in the MP-110, MP-150 and MP-200.
- Shure: Shure marketed its line-contact shape as “Hyperelliptical”.[24] We do not list Shure cartridges in our top list.
MM or MC: does the design change the shape?
No – shape and transducer principle are two separate questions. The Shibata exists in the 2M Black MM cartridge as well as in the Cadenza Black MC, MicroLine in the VM95ML as well as in the AT-OC9XML MC.[7][8][4][5] The practical difference lies in replacing the stylus: with MM cartridges such as the VM95, 2M or Goldring 1042 you swap the stylus yourself; with MC cartridges this is usually not possible, and one alternative is a re-tipping service that fits a new tip to the cantilever.[4][7][14][20] For MC you also need a suitable phono stage; models are in the phono preamp top list.
Stylus shapes compared: the table
The table sums up radii, alignment demands and stylus-life guide values. Count and price band refer to the cartridges in our top list by the shape in their data sheet.
| Shape | Radii r/R (examples, manufacturers) | Alignment demands | Life guide value (manufacturers) | In our list | Price band in the list |
|---|---|---|---|---|---|
| Spherical / conical | one radius, typ. 0.6 mil ≈ 15 µm[1] | low | about 300–500 h[2] | 3 cartridges | about €35–470 |
| Elliptical | 8/18 µm; 0.3 × 0.7 mil[7][4] | medium | about 300 h[2] | 21 cartridges | about €45–990 |
| Fine Line | 8/40 µm[7] | high | up to 1,000 h (Ortofon in general)[10] | 2 cartridges | about €350–1,499 |
| Shibata | 6/50 µm; 2.7 × 0.26 mil[7][4] | high | about 800 h[2] | 6 cartridges | about €190–2,999 |
| Line Contact / SLC | about 4–7 / 70 µm[18] | high | about 800 h (SLC)[2] | 5 cartridges | about €800–3,650 |
| MicroLine | 2.2 × 0.12 mil ≈ 56 × 3 µm[4] | very high | about 1,000 h[2] | 5 cartridges | about €150–3,700 |
| Micro Ridge | 2–3 / 70–80 µm[11] | very high | radius stays the same; no hour figure[11][12] | 2 cartridges | about €900–1,790 |
| Gyger | 6/70 µm (FG 70); 5 µm (1042)[8][14] | high | no figure found | 1 cartridge | about €380–450 |
| Replicant 100 | 5/100 µm[8] | very high | up to 1,000 h without loss, over 2,000 h in total[9] | 3 cartridges | about €2,300–6,999 |
Alignment demands: our classification based on the cited sources, not a measurement. Not counted: the Ortofon Stylus 10 replacement stylus and the Dynavector 10X5 MkII, whose shape is stated differently depending on the variant.
Which stylus shape for whom?
The following decision aid matches typical situations to a shape. It does not replace a look at your tonearm’s data sheet.
- Entry level, simple turntable, arm without azimuth or height adjustmentSpherical or elliptical bonded. Audio-Technica explicitly recommends the conical shape for simple and older players.[1] Examples: Audio-Technica AT-VM95C, Audio-Technica AT-VM95E, Ortofon 2M Red. Matching players: automatic turntables and the turntable top list.
- Old, used or worn recordsA spherical or elliptical shape is often the more relaxed choice here: Audio-Technica points out that Special Line Contact styli can make more surface noise audible on worn records.[1] For vintage mono LPs Audio-Technica recommends a conical stylus, for shellac a dedicated 78 stylus.[2][1]
- DJ use and scratchingSpherical – robust and common in DJ use.[6][24]
- Upgrading without a new cartridgeWithin a stylus-swap family: from the Audio-Technica AT-VM95E to the Audio-Technica AT-VM95ML or Audio-Technica AT-VM95SH, from the Ortofon 2M Red to the Ortofon 2M Blue.[4][7]
- Well-adjustable arm, lots of classical music or long record sidesShibata, Fine Line or MicroLine – this is where better inner-groove tracing pays off.[1][4][18] Examples: Ortofon 2M Bronze, Audio-Technica AT-VM95ML, Ortofon 2M Black.
- Many listening hours, stylus life mattersMicroLine or Micro Ridge: Audio-Technica gives 1,000 hours, and with Micro Ridge the contact radius stays the same over its life.[2][11][12]
- High-end turntable with SRA and azimuth adjustmentMicro Ridge, Special Line Contact or Replicant 100 – their potential requires very precise alignment.[22][21] Examples: Dynavector DV 20X2A, Audio-Technica AT-ART9XI, Ortofon Cadenza Bronze. Matching turntables: direct drive and belt drive.
Does the cartridge suit your turntable?
The shape is only part of the decision. Whether a cartridge works on your turntable also depends on compliance, effective arm mass, weight and phono stage. The compatibility hub calculates typical pairs; in the Vinyl BotPro Advisor (German) you put turntable, cartridge and phono stage together yourself. All cartridges with index, rank and price band are in the cartridge top list.
Frequently asked questions about stylus shapes
Which stylus shape is the best?
None for every case. Fine shapes such as Shibata, MicroLine or Replicant 100 trace the groove more accurately but need careful alignment and clean records; spherical and elliptical styli are more robust and cheaper. Soundsmith describes every shape as a compromise between cost, performance and alignment effort.[18]
How long does a cartridge stylus last?
For the VM series Audio-Technica gives about 300 hours (elliptical) to 1,000 hours (MicroLine) depending on the shape; Ortofon gives up to 1,000 hours in general with proper care and more than 2,000 hours of total life for the Replicant 100 stylus. Only a microscope check gives certainty.[2][10][9][18]
What is the difference between nude and bonded?
On bonded styli only the diamond tip is glued to a metal shank; this is cheaper but adds mass to the cantilever. Nude styli are a whole diamond, lighter and, according to Audio-Technica, longer-lasting.[1]
Can I swap only the stylus to get a different shape?
With many MM cartridges, yes. The Audio-Technica VM95 family has six interchangeable styli; at Ortofon the styli of the 2M Red and 2M Blue fit each other, as do those of the 2M Bronze and 2M Black. With MC cartridges this is usually not possible.[4][7]
Do I need to set the SRA with a Shibata or MicroLine stylus?
It should be right. With spherical styli the rake angle hardly matters, with elliptical and line-contact shapes it does. Michael Fremer recommends 92 degrees; one degree corresponds to about 4 mm of height change at the pivot of a 9-inch arm.[22]
Do fine stylus shapes damage my records?
Not when properly aligned – on the contrary, Orbray describes that the Shibata’s longer contact line lowers pressure and spares record and stylus. Misaligned or worn styli are the risk: Sumiko warns that narrow shapes can damage the groove when misaligned.[11][19][18]
Which shape for shellac records and vintage mono LPs?
78s need a larger radius: Audio-Technica gives 2.5 mil, Ortofon 65 µm for the 2M 78 stylus. For vintage mono LPs Audio-Technica recommends a conical stylus.[1][7][2]
Did the AI listen to or measure the cartridges?
No. Vinyl BotPro evaluated manufacturer documents and international literature; there is neither a listening test nor our own measurement. How index and rank are created is explained in the methodology.
Sources
All links checked on 6 Oct 2026. Manufacturer and international sources; radii and hour figures come from the makers named.
- Audio-Technica: „Understanding the different stylus shapes“ (Support-Artikel). audio-technica.com (accessed 6 Oct 2026)
- Audio-Technica: „Audio Solutions Question of the Week: How do I select a replacement or upgrade stylus for my Audio-Technica VM Series phono cartridge?“. audio-technica.com (accessed 6 Oct 2026)
- Audio-Technica: “Upgrading your cartridge” (press release). audio-technica.com (accessed 6 Oct 2026)
- Audio-Technica: product pages AT-VM95ML, AT-VM95C, AT-VM95E, AT-VM95EN, AT-VM95SH (specifications). audio-technica.com/at-vm95ml · audio-technica.com/at-vm95c · audio-technica.com/at-vm95e · audio-technica.com/at-vm95en · audio-technica.com/at-vm95sh (accessed 6 Oct 2026)
- Audio-Technica: product pages AT-OC9XML and AT-ART9XI (specifications). audio-technica.com/at-oc9xml · audio-technica.com/at-art9xi (accessed 6 Oct 2026)
- Ortofon: „Elliptical or spherical stylus on cartridges – what’s the difference?“ (Blog). ortofon.com (accessed 6 Oct 2026)
- Ortofon: 2M Series – Moving Magnet Cartridges (brochure, PDF, 2020). ortofon.com (accessed 6 Oct 2026)
- Ortofon: MC Cadenza Series (data sheet, PDF). ortofon.com (accessed 6 Oct 2026)
- Ortofon: „The Ortofon Replicant 100 – the finest diamond in the world“. ortofon.com (accessed 6 Oct 2026)
- Ortofon: FAQ (stylus life, alignment). ortofon.com (accessed 6 Oct 2026)
- Orbray (formerly Namiki): Stylus – profiles and radii of diamond stylus tips. orbray.com (accessed 6 Oct 2026)
- Dynavector: „Micro Ridge stylus“. dynavector.com (accessed 6 Oct 2026)
- Dynavector: DV 20X2-H/L (product page). dynavector.com (accessed 6 Oct 2026)
- Goldring: product pages 1042 and E2 (specifications). goldring.co.uk/goldring-1042-cartridge.html · goldring.co.uk/goldring-e2.html (accessed 6 Oct 2026)
- Nagaoka: MP-500 (product page, Japanese). nagaoka.co.jp (accessed 6 Oct 2026)
- Hana: product pages SL MK II and Umami Red. hanacartridges.com/hana-sl-mk-ii · hanacartridges.com/hana-umami-red (accessed 6 Oct 2026)
- Denon: DL-103R (product page, Japanese). denon.com (accessed 6 Oct 2026)
- Soundsmith: „Stylus Shape Information“. sound-smith.com (accessed 6 Oct 2026)
- Sumiko: „What is a phono cartridge?“ (Cartridge 101). sumikophonocartridges.com (accessed 6 Oct 2026)
- Expert Stylus & Cartridge Co.: stylus making, retipping and microscope inspection. expertstylus.co.uk (accessed 6 Oct 2026)
- Michael Fremer: “Analog Corner #322”, Stereophile, May 2022. stereophile.com (accessed 6 Oct 2026)
- Michael Fremer: “How to Use a USB Digital Microscope to set 92 Degree Stylus Rake Angle (SRA)”, AnalogPlanet, 29 Jun 2012. analogplanet.com (accessed 6 Oct 2026)
- Basil Lane: “Improving Groove Contact”, Hi-Fi News (first published 1980, online 2019). hifinews.com (accessed 6 Oct 2026)
- Wikipedia (English): “Phonograph”, section Stylus. en.wikipedia.org (accessed 6 Oct 2026)
- Vinyl Engine Forum: „Advanced Stylus Shapes: Pics, discussion, patents“. vinylengine.com (accessed 6 Oct 2026)
Orientation only, prices without guarantee, check the manufacturer’s specifications. Assessment by the AI Vinyl BotPro based on manufacturer data and literature, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability
Updated 6 Oct 2026 · As of Oct 2026 · Graphics: VinylCination, own illustration