Compatibility · Oct 2026

Goldring 1042 on the SME Model 6: does it fit?

Does the Goldring 1042 fit the tonearm of the SME Model 6? With 9.5 g of effective arm mass and 6.3 g for the cartridge the calculation gives 12.3 Hz; verdict: borderline. Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: borderline Resonance 12.3 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: borderline

Borderline: at least one point is at the edge. Checks at the edge: Resonance.

  • Resonance: 12.3 Hz
  • Moving mass: 16.8 g
  • Compliance: 10 µm/mN at 10 Hz
  • Cartridge: 6.3 g

At 10 µm/mN the Goldring 1042 is a stiff cartridge. On the SME M2-9 (9.5 g effective mass) that gives about 12.3 Hz, just above the target zone; since the value comes without conversion there is no range. Counterweight (5 to 12 g) and half-inch mount are documented. With its heavier arm than the RPM 5, the SME brings the resonance a little lower than there (12.9 Hz).

Resonance band: Goldring 1042 on SME Model 6 Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 12.3 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 12.3 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz).

The calculation in detail

Whether arm and cartridge work together depends on mounting, resonance and counterweight. Each point is rated on its own, and the verdict follows the worst result.

  • Mountingfits

    The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.

    Advisor output: Removable headshell with half-inch mount (manufacturer).

  • Resonanceborderline

    The resonance of 12.3 Hz is above the target zone. The higher it rises, the closer it gets to audible bass; up to 14 Hz this counts as a warning, not as an exclusion.

    Advisor output: fᵣ ≈ 12.3 Hz by 159 / √(16.8 × 10); target 8–12 Hz, warning outside 7–14 Hz. Mass 9.5 g arm + 6.3 g cartridge + 1 g screws = 16.8 g; compliance 10 µm/mN (10 Hz, per data sheet). Calculation note, not a measurement.

  • Counterweightfits

    The arm’s counterweight covers the cartridge: 6.3 g lies within the range 5–12 g.

    Advisor output: Cartridge 6.3 g is within the range 5–12 g (cartridge weight (SME: cartridge balance range 5–12 g)).

How the resonance comes about

  1. Moving mass: 9.5 g arm + 6.3 g cartridge + 1 g screws = 16.8 g.
  2. Compliance at 10 Hz: The compliance of 10 µm/mN is specified at 10 Hz and is used unchanged.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(16.8 × 10) = 159 / √168 ≈ 12.3 Hz.

The input data

Tonearm: SME M2-9 (SME Model 6)

Effective mass
9.5 g · manufacturer figure, source: sme.co.uk
Mounting
removable headshell, half-inch mount
Counterweight
5–12 g · cartridge weight (SME: cartridge balance range 5–12 g)

Cartridge: Goldring 1042

Type
MM · Nude Gyger S line contact
Weight
6.3 g
Compliance
10 µm/mN at 10 Hz
Tracking force
1.5–2.0 g · recommended 1.7 g
Output voltage
6.5 mV
Market price
about €380–450 (prices without guarantee, Oct 2026)

In our data there is no fixed factory cartridge documented for the SME Model 6. The calculation applies to a cartridge of your own choice.

Next steps

  • Check the highlighted points above (Resonance) in the manufacturer’s documents.
  • If needed, ask a dealer or the manufacturer whether the combination is recommended in everyday use.
  • If you are unsure, look for a cartridge that passes all three checks (see the alternatives below).

The Goldring 1042 is a moving-magnet cartridge (6.5 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: Anyone who can use MC will find an alternative in the Audio-Technica AT-OC9XEN (about €280–370) with 7.6 g and 9.3 Hz on the SME arm.

More cartridges on the SME Model 6

Also unproblematic on paper on the SME Model 6 are these cartridges in a comparable price range (without guarantee):

The Goldring 1042 on other turntables

If you would rather change the turntable: on these models the Goldring 1042 passes all three checks:

Method in brief

Procedure
Following the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Can I run the Goldring 1042 on the SME Model 6?

With reservations. The Goldring 1042 on the SME Model 6 is borderline; Resonance is at the edge of the target zone. Calculated resonance: 12.3 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.

What resonance frequency results for the Goldring 1042 on the SME Model 6?

About 12.3 Hz. The calculation uses 159 / √(mass × compliance): 16.8 g moving mass (arm 9.5 g, cartridge 6.3 g, screws 1 g) and 10 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the SME Model 6 sufficient for the Goldring 1042?

The arm’s counterweight covers the cartridge: 6.3 g lies within the range 5–12 g.

What phono input does the Goldring 1042 need?

The Goldring 1042 is a moving-magnet cartridge (6.5 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet. Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026