Compatibility · Oct 2026
Nagaoka MP-500 on the SME Model 6: does it fit?
We worked through the tonearm of the SME Model 6 (SME M2-9, 9.5 g effective mass) and the cartridge Nagaoka MP-500 (8 g) with the calculation method of our Advisor. Result: fits, calculated resonance 9.5 Hz (range 8.5–10.4 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.
Verdict: fits
Fits according to our calculation. All three checks (mounting, resonance, counterweight) pass.
- Resonance: 9.5 Hz (range 8.5–10.4 Hz)
- Moving mass: 18.5 g
- Compliance: 15.3 µm/mN at 10 Hz
- Cartridge: 8 g
At 8.0 g the Nagaoka MP-500 is a relatively heavy cartridge and fits the SME’s counterweight range (5 to 12 g) well. The resonance reaches about 9.5 Hz with a range of 8.5 to 10.4 Hz: completely inside the target zone. According to our test page the cartridge costs about €800 to 900, which suits the turntable’s price (about €6,000 to 8,000) better than the entry-level cartridges of this series.
The calculation in detail
Three points decide whether a cartridge fits a tonearm: the mounting, the resonance of arm and cartridge, and the counterweight. The overall verdict is as strict as the weakest point.
-
Mountingfits
The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.
Advisor output: Removable headshell with half-inch mount (manufacturer).
-
Resonancefits
The calculated resonance of 9.5 Hz lies in the target zone. The rule-of-thumb range stays within the warning limits.
Advisor output: fᵣ ≈ 9.5 Hz (range 8.5–10.4 Hz) by 159 / √(18.5 × 15.3); target 8–12 Hz, warning outside 7–14 Hz. Mass 9.5 g arm + 8 g cartridge + 1 g screws = 18.5 g; compliance 8.5 ·10⁻⁶ cm/dyn at 100 Hz × 1.5–2.2 ≈ 12.8–18.7 µm/mN at 10 Hz (rule of thumb, middle 15.3). Calculation note, not a measurement.
-
Counterweightfits
The arm’s counterweight covers the cartridge: 8 g lies within the range 5–12 g.
Advisor output: Cartridge 8 g is within the range 5–12 g (cartridge weight (SME: cartridge balance range 5–12 g)).
How the resonance comes about
- Moving mass: 9.5 g arm + 8 g cartridge + 1 g screws = 18.5 g.
- Compliance at 10 Hz: The compliance of 8.5×10⁻⁶ cm/dyn is specified at 100 Hz. For 10 Hz the rule of thumb is 1.5 to 2.2 times that, i.e. 12.8 to 18.7 µm/mN; the calculation uses the middle (factor 1.8): 15.3 µm/mN.
- Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(18.5 × 15.3) = 159 / √283.1 ≈ 9.5 Hz.
- Range: Because the compliance is converted, the result is 8.5–10.4 Hz (worst and best case).
The input data
Tonearm: SME M2-9 (SME Model 6)
- Effective mass
- 9.5 g · manufacturer figure, source: sme.co.uk
- Mounting
- removable headshell, half-inch mount
- Counterweight
- 5–12 g · cartridge weight (SME: cartridge balance range 5–12 g)
Cartridge: Nagaoka MP-500
- Type
- MP · Line Contact · boron cantilever
- Weight
- 8 g
- Compliance
- 8.5×10⁻⁶ cm/dyn at 100 Hz
- Tracking force
- 1.3–1.8 g · recommended 1.6 g
- Output voltage
- 3 mV
- Market price
- about €800–900 (prices without guarantee, Oct 2026)
In our data there is no fixed factory cartridge documented for the SME Model 6. The calculation applies to a cartridge of your own choice.
What this means for you
- Set the tracking force as specified by the manufacturer (1.3–1.8 g · recommended 1.6 g) and check it with a gauge.
- Set the overhang with the alignment protractor, then the anti-skating.
- Compare the manufacturer’s specifications for arm and cartridge before you order or mount.
The Nagaoka MP-500 is a moving-magnet cartridge (3 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
Alternatives
Our tip: The MP-500 also stays in the target zone on the Pro-Ject X8 Evolution at 9.7 Hz; the arm has 8.5 g there, and the turntable is priced well below the SME.
More cartridges on the SME Model 6
If you would like to compare: these cartridges also pass all three checks on the SME Model 6 and cost roughly the same according to our test pages (prices without guarantee):
- Ortofon 2M Black LVB 250: calculated resonance 8.1 Hz, 7.2 g, about €850–999
- Ortofon Cadenza Red: calculated resonance 10 Hz, 10.7 g, about €1,236–1,499
- Nagaoka MP-200: calculated resonance 10.7 Hz, 6.5 g, about €400–480
- Audio-Technica AT-OC9XEN: calculated resonance 9.3 Hz, 7.6 g, about €280–370
The Nagaoka MP-500 on other turntables
On these turntables the Nagaoka MP-500 passes all three checks according to the calculation:
- Pro-Ject X8 Evolution: calculated resonance 9.7 Hz, arm 8.5 g
- Technics SL-1200GR2: calculated resonance 9.7 Hz, arm 8.5 g
- Pro-Ject RPM 5 Carbon: calculated resonance 9.9 Hz, arm 8 g
- Pro-Ject X2 B: calculated resonance 8.6 Hz, arm 13.5 g
Method in brief
- Procedure
- As in the Advisor: resonance fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
- Verdict rule
- One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
- Data
- Advisor data of 2 Oct 2026, page of 3 Oct 2026
- Limits
- No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.
Frequently asked questions
Does the Nagaoka MP-500 fit the SME Model 6?
Yes, according to our calculation the Nagaoka MP-500 fits the SME Model 6: mounting, resonance and counterweight pass. Calculated resonance: 9.5 Hz (range 8.5–10.4 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.
How high is the resonance of the Nagaoka MP-500 and the SME Model 6?
About 9.5 Hz (range 8.5–10.4 Hz). The calculation uses 159 / √(mass × compliance): 18.5 g moving mass (arm 9.5 g, cartridge 8 g, screws 1 g) and 15.3 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.
Is the counterweight of the SME Model 6 sufficient for the Nagaoka MP-500?
The arm’s counterweight covers the cartridge: 8 g lies within the range 5–12 g.
What phono input does the Nagaoka MP-500 need?
The Nagaoka MP-500 is a moving-magnet cartridge (3 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
How reliable is this calculation?
It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet, converted with a rule of thumb (factor 1.5–2.2 for 100 Hz values). Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.
Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability
Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026