Compatibility · Oct 2026

Ortofon 2M Red on the Pro-Ject X2 B: does it fit?

Does the Ortofon 2M Red fit the tonearm of the Pro-Ject X2 B? With 13.5 g of effective arm mass and 7.2 g for the cartridge the calculation gives 7.6 Hz; verdict: borderline. Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: borderline Resonance 7.6 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: borderline

Borderline: at least one point is at the edge. Checks at the edge: Resonance.

  • Resonance: 7.6 Hz
  • Moving mass: 21.7 g
  • Compliance: 20 µm/mN at 10 Hz
  • Cartridge: 7.2 g

The X2 B ships with an Ortofon MC cartridge (Quintet Red), so the 2M Red would be a switch to a moving-magnet cartridge. The counterweight No. 31 of the 9-inch arm covers 7 to 12 g, and the 2M Red fits inside. The critical point is the arm mass of 13.5 g: together with the relatively soft cartridge the resonance drops to about 7.6 Hz, below the target zone but still above the warning limit of 7 Hz. That gives “borderline”.

Resonance band: Ortofon 2M Red on Pro-Ject X2 B Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 7.6 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 7.6 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz).

The calculation in detail

Whether arm and cartridge work together depends on mounting, resonance and counterweight. Each point is rated on its own, and the verdict follows the worst result.

  • Mountingfits

    The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.

    Advisor output: Fixed headshell with half-inch mounting holes (manufacturer: cartridges with a half-inch mount fit).

  • Resonanceborderline

    The resonance of 7.6 Hz is below the target zone. Low resonances react more strongly to warped records and footfall; below 7 Hz this counts as a warning, not as an exclusion.

    Advisor output: fᵣ ≈ 7.6 Hz by 159 / √(21.7 × 20); target 8–12 Hz, warning outside 7–14 Hz. Mass 13.5 g arm + 7.2 g cartridge + 1 g screws = 21.7 g; compliance 20 µm/mN (10 Hz, per data sheet). Calculation note, not a measurement.

  • Counterweightfits

    The arm’s counterweight covers the cartridge: 7.2 g lies within the range 7–12 g.

    Advisor output: Cartridge 7.2 g is within the range 7–12 g (cartridge weight (Pro-Ject: counterweight No. 31 for 7–12 g)).

How the resonance comes about

  1. Moving mass: 13.5 g arm + 7.2 g cartridge + 1 g screws = 21.7 g.
  2. Compliance at 10 Hz: The compliance of 20 µm/mN is specified at 10 Hz and is used unchanged.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(21.7 × 20) = 159 / √434 ≈ 7.6 Hz.

The input data

Tonearm: Pro-Ject 9 carbon/alu sandwich (Pro-Ject X2 B)

Effective mass
13.5 g · manufacturer figure, source: project-audio.com
Mounting
fixed headshell with half-inch mount
Counterweight
7–12 g · cartridge weight (Pro-Ject: counterweight No. 31 for 7–12 g)

Cartridge: Ortofon 2M Red

Type
MM · elliptical bonded (r/R 8/18 µm)
Weight
7.2 g
Compliance
20 µm/mN at 10 Hz
Tracking force
1.6–2.0 g (recommended 1.8 g)
Output voltage
5.5 mV
Market price
about €85–100 (prices without guarantee, Oct 2026)

According to the manufacturer the Pro-Ject X2 B ships with a different cartridge (Ortofon Quintet Red (MC)). The calculation here therefore describes a swap, i.e. an upgrade scenario.

Next steps

  • Check the highlighted points above (Resonance) in the manufacturer’s documents.
  • If needed, ask a dealer or the manufacturer whether the combination is recommended in everyday use.
  • If you are unsure, look for a cartridge that passes all three checks (see the alternatives below).

The Ortofon 2M Red is a moving-magnet cartridge (5.5 mV) and works on a normal MM phono input. If the Pro-Ject X2 B has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: If moving coil is an option, the Audio-Technica AT-OC9XEN (about €280–370) fits cleanly on paper: 7.6 g and 8.4 Hz on the heavy arm.

More cartridges on the Pro-Ject X2 B

Also unproblematic on paper on the Pro-Ject X2 B are these cartridges in a comparable price range (without guarantee):

The Ortofon 2M Red on other turntables

If you would rather change the turntable: on these models the Ortofon 2M Red passes all three checks:

Method in brief

Procedure
Following the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Can I run the Ortofon 2M Red on the Pro-Ject X2 B?

With reservations. The Ortofon 2M Red on the Pro-Ject X2 B is borderline; Resonance is at the edge of the target zone. Calculated resonance: 7.6 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.

What resonance frequency results for the Ortofon 2M Red on the Pro-Ject X2 B?

About 7.6 Hz. The calculation uses 159 / √(mass × compliance): 21.7 g moving mass (arm 13.5 g, cartridge 7.2 g, screws 1 g) and 20 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the Pro-Ject X2 B sufficient for the Ortofon 2M Red?

The arm’s counterweight covers the cartridge: 7.2 g lies within the range 7–12 g.

What is fitted to the Pro-Ject X2 B at the factory?

According to the manufacturer the Pro-Ject X2 B ships with a different cartridge (Ortofon Quintet Red (MC)). The calculation here therefore describes a swap, i.e. an upgrade scenario.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet. Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026