Speaker cable · Short analysis · Premium, rank 8

in-akustik Referenz LS-502 Review

Short analysis (research): 2 × 2.97 mm² · high purity copper, sold by the metre, without plugs — manufacturer specifications and retailer prices, no listening test.

AI research Premium Short analysis Index 60 Price as of Sept 2026

Summary

in-akustik Referenz LS-502 (Bulk cable sold by the metre, Twisted Pair): 2 × 2.97 mm² · high purity copper; sold by the metre, without plugs. Price: approx. €22.40/m · Price as of Sept 2026. The Concentric Copper Construction arranges the strands in a fixed position; the practical use with usual lengths is not documented, the build quality (PE mesh jacket, Made in Germany) is documented.

At usual lengths (up to approx. 5–10 m), what matters most is an adequate cross-section and a clean, firm connection; audible sound differences between speaker cables are scientifically disputed.

Assumptions

  • Prices: consumer prices incl. VAT, as of Sept 2026 (manufacturer or retailer page); they may change
  • Details from the manufacturer’s shop or datasheet, or the retailer’s page; availability may differ and was not checked for every variant.
  • Living-room system with cable runs of up to approx. 5–10 m
  • No measurements or listening tests of our own

Specs (public / manufacturer)

TypeSold by the metre · Twisted Pair
Cross-section / conductor2 × 2.97 mm² · High purity copper
Conductor materialPure copper, Concentric Copper Construction
ConstructionTwisted Pair, Dielectric DUO-PE II, PE mesh jacket, Ø 8.5 mm
Termination / connectionSold by the metre, no plugs
LengthSold by the metre
Manufacturer / originin-akustik, Made in Germany
Price guideSold by the metre, 22.40 €/m · Price as of Sept 2026
Manufacturer specifications (in-akustik)
Manufacturer data sheet
Typehigh-end speaker cable, by the metre
Cross-section2 × 2.97 mm²
Conductorhigh-purity copper, concentric copper (2 cores of 37 wires)
Designtwisted pair
InsulationDUO-PE II, PE network jacket
Outer diameter8.5 mm
Resistancenot specified by manufacturer

Source: in-akustik – official specifications · As of 16 October 2026 · subject to change by the manufacturer

Suits / less suited

  • Suits: cable runs up to approx. 8 m
  • Suits: Who appreciates build quality "Made in Germany"
  • Less suited: Price conscious buyers

Vinyl BotPro Index: 60 (Premium 55–69) · Label: AI research · Sept 2026 · All information is provided without guarantee; prices change and manufacturer specifications may differ.

Manufacturer and concept

in-akustik is a cable maker based in Ballrechten-Dottingen in Germany's Black Forest and builds many of its Referenz cables in Germany. The Referenz series ranges from simple two-conductor cables like the LS-502 up to elaborate Air models with air insulation. The LS-502 is a twisted-pair cable sold by the metre without connectors, with a cross-section of 2 × 2.97 mm². At around €22.40 per metre (no guarantee), it sits in our premium tier.

We found no English-language reviews of the LS-502 in the international trade press. This page therefore relies on the manufacturer's data, the physics of speaker cables and practical advice on installation. There are no own listening or measurement tests.

The technology explained

Conductors: Concentric Copper

According to in-akustik, each of the two conductors consists of 37 strands of high-purity copper. In the Concentric Copper design, these strands sit in fixed layers around a centre strand instead of being loosely twisted. That keeps the geometry constant along the whole length. The manufacturer cites more uniform electrical properties as the reason. Whether this is audible at normal cable lengths has not been demonstrated.

Twisted pair

The two conductors are twisted together. Twisted conductors pick up less external interference and radiate less, because the magnetic fields of the outgoing and return conductors largely cancel each other. The cable's inductance is also lower than with parallel conductors spaced further apart. Low inductance is an advantage above all with long cables and at high frequencies.

Insulation and jacket

in-akustik uses DUO-PE II, a polyethylene compound, as insulation. Polyethylene has favourable electrical properties and is therefore also used in high-frequency cables. A PE mesh jacket protects the cable on the outside. The outer diameter is 8.5 mm: thick enough for robust installation, yet still flexible enough for corners and cable ducts.

What a speaker cable really has to do

A speaker cable should carry current from the amplifier to the speaker with as little loss as possible. The decisive factor is resistance, which depends on cross-section and length. Copper has a resistivity of about 0.0172 Ω·mm²/m. At 2.97 mm² that gives roughly 0.0058 Ω per metre and conductor.

An example: with 5 m of cable, the current flows through 10 m of conductor, out and back. That gives about 0.058 Ω. With a 4 Ω speaker this is around 1.4% of the load, a level loss of about 0.13 dB. At 10 m it is about 0.12 Ω and 0.25 dB. These values are very small. Damping factor matters too: the lower the cable resistance, the better the amplifier can control the woofer's movement. At 2.97 mm², the cable stays in an uncritical range at living-room lengths.

Capacitance and inductance play a smaller role in speaker cables within the audible range. Very exotic cables with very high capacitance can make some amplifiers unstable. A twisted two-conductor cable like the LS-502 is uncritical here. in-akustik gives no figures for resistance, capacitance or inductance for the LS-502, so the numbers above are calculated from the cross-section and are not manufacturer data.

Sound differences: what is proven

Whether speaker cables with an adequate cross-section sound audibly different is scientifically disputed. In controlled blind tests, differences can usually only be shown when resistance or length differ markedly. We therefore make no claims about a sound of its own for the LS-502. What is documented is an adequate cross-section, careful workmanship and a solid construction.

Which length and which cross-section?

For lengths up to about 5 m, 2.5 mm² is enough in most cases. Up to about 10 m, 4 mm² is a safe choice, especially with 4 Ω speakers. At 2.97 mm², the LS-502 sits in between and works well for runs up to about 8 m. Both channels do not have to be exactly the same length. Propagation time differences in the cable are inaudibly small, and resistance differences are negligible at short lengths. Equal lengths do no harm and look tidier, though.

Termination: connectors or bare wire

The LS-502 is supplied by the metre without connectors. The bare end can go straight into the terminals of amplifier and speaker. Twist the strands well so no single strand sticks out. A stray strand can cause a short circuit and, in the worst case, damage the amplifier.

Banana plugs or spade lugs are cleaner. Banana plugs make reconnecting easy; spades sit especially firmly under a binding post. Wire ferrules are an inexpensive alternative for bare ends. What matters is that connectors and terminals fit well and are firmly tightened. A loose contact raises contact resistance far more than any difference between two good cables.

Stripping step by step

First separate the two conductors over about 5 to 8 cm. Carefully slit the mesh jacket lengthways with a sharp knife without nicking the conductor insulation. Then remove about 12 to 15 mm of insulation from each conductor. A wire stripper of the right size protects the fine strands. Cutting off strands reduces the cross-section at that point. Then twist the strands tightly and insert them into the plug, lug or ferrule, depending on the connection.

Bare copper ends tarnish over time. The oxide layer slightly raises contact resistance. Without connectors, you can simply strip the ends afresh after a few years. With connectors, check that they are still tight. Tinning is not a good idea with screw terminals, because solder slowly deforms under pressure and the contact can loosen.

How much budget for cables?

A speaker cable cannot make a system better than its amplifier and speakers allow. It can, however, create weaknesses if the cross-section is too small or the contacts are poor. The sensible order is to ensure an adequate cross-section and clean connections first. A cable like the LS-502 meets those requirements. If you want to keep the cable budget tight, money is better spent on better speakers, their placement or room acoustics. The differences there are far greater.

Cable and amplifier

Modern transistor amplifiers have a very low output impedance. Cable resistance then weighs relatively more, but stays small at 2.97 mm². Valve amplifiers have a higher output impedance, so cable resistance matters even less. With speakers whose impedance varies strongly, a cable that is too thin can slightly alter the frequency response. With the LS-502's cross-section this is not an issue at normal lengths. Suitable amplifiers can be found in our best amplifiers.

Routing and polarity

The conductors can be told apart by colour or marking. Positive must be on the same conductor at the amplifier and at the speaker. If one channel is wired out of phase, bass goes missing and the centre image blurs. Do not run speaker cables closely parallel to mains cables over long distances; crossing at right angles is no problem. A twisted cable like the LS-502 is less sensitive here anyway. Do not coil excess length tightly; shorten it instead.

Installation in walls and ducts

If you want to run speaker cable inside a wall or a conduit, check first whether the cable is approved for it. Fire-safety rules apply to in-wall installation in many countries. in-akustik gives no information on this for the LS-502. In a cable duct or behind a skirting board, the robust jacket keeps the cable well protected. Make sure it is not kinked or crushed by furniture edges. With an 8.5 mm diameter, allow a generous bend radius so the strands inside do not break. When pulling it through conduit, a draw cord prevents overstretching.

Bi-wiring and bi-amping

If a speaker has two pairs of terminals, separate cables can be run to the tweeter and woofer sections. This is called bi-wiring. It requires two lengths of LS-502 per speaker. The benefit is disputed, but it does no harm. With bi-amping, a separate amplifier drives each section. If you use only one cable, leave the jumpers on the terminals in place.

Strengths and limits at a glance

Who it suits

The LS-502 suits buyers looking for a well-made cable with an adequate cross-section who value manufacturing in Germany. If you only need the cross-section and want to save money, cheaper alternatives include the Supra Classic 2x2.5 or the Oehlbach Speaker Wire SP-25.

Compared with alternatives

The in-akustik Referenz LS-602 is the next step in the series. The QED Performance Speaker Cable and the Chord Company ClearwayX are alternatives from British makers. More in our best speaker cables.

in-akustik Referenz LS-502 FAQ

How long can the cable be?

At 2.97 mm², runs up to about 8 m are uncritical.

Do I need connectors?

No, bare ends work. Banana plugs or spade lugs are cleaner.

Do both cables have to be the same length?

Not necessarily. At living-room lengths, differences are negligible.

Does it sound different from cheaper cables?

That is scientifically disputed. Cross-section and workmanship are documented.

Is it suitable for bi-wiring?

Yes, with two lengths per speaker.

Verdict

The in-akustik Referenz LS-502 is a solidly built, twisted two-conductor cable with 2 × 2.97 mm² of high-purity copper. For typical living-room lengths the cross-section is adequate, and the construction is low-interference and robust. If you value workmanship and origin, this is a good choice. If cross-section is all you care about, you can buy cheaper.