Compatibility · Oct 2026

Audio-Technica AT-VM740ML on the Pro-Ject X2 B: does it fit?

We worked through the tonearm of the Pro-Ject X2 B (Pro-Ject 9 carbon/alu sandwich, 13.5 g effective mass) and the cartridge Audio-Technica AT-VM740ML (8 g) with the calculation method of our Advisor. Result: borderline, calculated resonance 7.9 Hz (range 7.1–8.7 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: borderline Resonance 7.9 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: borderline

Borderline: at least one point is at the edge. Checks at the edge: Resonance.

  • Resonance: 7.9 Hz (range 7.1–8.7 Hz)
  • Moving mass: 22.5 g
  • Compliance: 18 µm/mN at 10 Hz
  • Cartridge: 8 g

With 8.0 g the AT-VM740ML lies within the X2 B’s counterweight range (7 to 12 g). On the heavy arm (13.5 g) the resonance slips to about 7.9 Hz with a range of 7.1 to 8.7 Hz: the lower edge of the range is only just above the warning limit of 7 Hz. The calculation therefore stands at “borderline”, even though mounting and counterweight fit.

Resonance band: Audio-Technica AT-VM740ML on Pro-Ject X2 B Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 7.9 Hz, range 7.1 to 8.7 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 7.9 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz). The grey bar shows the rule-of-thumb range.

The calculation in detail

Three points decide whether a cartridge fits a tonearm: the mounting, the resonance of arm and cartridge, and the counterweight. The overall verdict is as strict as the weakest point.

  • Mountingfits

    The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.

    Advisor output: Fixed headshell with half-inch mounting holes (manufacturer: cartridges with a half-inch mount fit).

  • Resonanceborderline

    The resonance of 7.9 Hz is below the target zone. Low resonances react more strongly to warped records and footfall; below 7 Hz this counts as a warning, not as an exclusion.

    Advisor output: fᵣ ≈ 7.9 Hz (range 7.1–8.7 Hz) by 159 / √(22.5 × 18); target 8–12 Hz, warning outside 7–14 Hz. Mass 13.5 g arm + 8 g cartridge + 1 g screws = 22.5 g; compliance 10 ·10⁻⁶ cm/dyn at 100 Hz × 1.5–2.2 ≈ 15–22 µm/mN at 10 Hz (rule of thumb, middle 18). Calculation note, not a measurement.

  • Counterweightfits

    The arm’s counterweight covers the cartridge: 8 g lies within the range 7–12 g.

    Advisor output: Cartridge 8 g is within the range 7–12 g (cartridge weight (Pro-Ject: counterweight No. 31 for 7–12 g)).

How the resonance comes about

  1. Moving mass: 13.5 g arm + 8 g cartridge + 1 g screws = 22.5 g.
  2. Compliance at 10 Hz: The compliance of 10×10⁻⁶ cm/dyn is specified at 100 Hz. For 10 Hz the rule of thumb is 1.5 to 2.2 times that, i.e. 15 to 22 µm/mN; the calculation uses the middle (factor 1.8): 18 µm/mN.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(22.5 × 18) = 159 / √405 ≈ 7.9 Hz.
  4. Range: Because the compliance is converted, the result is 7.1–8.7 Hz (worst and best case).

The input data

Tonearm: Pro-Ject 9 carbon/alu sandwich (Pro-Ject X2 B)

Effective mass
13.5 g · manufacturer figure, source: project-audio.com
Mounting
fixed headshell with half-inch mount
Counterweight
7–12 g · cartridge weight (Pro-Ject: counterweight No. 31 for 7–12 g)

Cartridge: Audio-Technica AT-VM740ML

Type
VM Dual-MM · Nude MicroLine 0.12×2.2 mil
Weight
8 g
Compliance
10×10⁻⁶ cm/dyn at 100 Hz
Tracking force
1.8–2.2 g · recommended 2.0 g
Output voltage
4 mV
Market price
about €280–340 (prices without guarantee, Oct 2026)

According to the manufacturer the Pro-Ject X2 B ships with a different cartridge (Ortofon Quintet Red (MC)). The calculation here therefore describes a swap, i.e. an upgrade scenario.

What this means for you

  • Check the highlighted points above (Resonance) in the manufacturer’s documents.
  • If needed, ask a dealer or the manufacturer whether the combination is recommended in everyday use.
  • If you are unsure, look for a cartridge that passes all three checks (see the alternatives below).

The Audio-Technica AT-VM740ML is a moving-magnet cartridge (4 mV) and works on a normal MM phono input. If the Pro-Ject X2 B has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: Anyone looking for more headroom on the resonance will find it with the Nagaoka MP-500 (about €800–900): 8 g and 8.6 Hz on the X2 B.

More cartridges on the Pro-Ject X2 B

According to the calculation these cartridges pass all three checks on the Pro-Ject X2 B and cost roughly the same according to our test pages (prices without guarantee):

The Audio-Technica AT-VM740ML on other turntables

On these turntables the Audio-Technica AT-VM740ML passes all three checks according to the calculation:

Method in brief

Procedure
As in the Advisor: resonance fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Does the Audio-Technica AT-VM740ML fit the Pro-Ject X2 B?

With reservations. The Audio-Technica AT-VM740ML on the Pro-Ject X2 B is borderline; Resonance is at the edge of the target zone. Calculated resonance: 7.9 Hz (range 7.1–8.7 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.

How high is the resonance of the Audio-Technica AT-VM740ML and the Pro-Ject X2 B?

About 7.9 Hz (range 7.1–8.7 Hz). The calculation uses 159 / √(mass × compliance): 22.5 g moving mass (arm 13.5 g, cartridge 8 g, screws 1 g) and 18 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the Pro-Ject X2 B sufficient for the Audio-Technica AT-VM740ML?

The arm’s counterweight covers the cartridge: 8 g lies within the range 7–12 g.

What is fitted to the Pro-Ject X2 B at the factory?

According to the manufacturer the Pro-Ject X2 B ships with a different cartridge (Ortofon Quintet Red (MC)). The calculation here therefore describes a swap, i.e. an upgrade scenario.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet, converted with a rule of thumb (factor 1.5–2.2 for 100 Hz values). Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026