Compatibility · Oct 2026

Ortofon 2M Red on the Rega Planar 3: does it fit?

We worked through the tonearm of the Rega Planar 3 (Rega RB330, 11 g effective mass) and the cartridge Ortofon 2M Red (7.2 g) with the calculation method of our Advisor. Result: not verifiable, calculated resonance 8.1 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: not verifiable Resonance 8.1 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: not verifiable

Not verifiable: key data is missing. Checks open: Mounting, Counterweight.

  • Resonance: 8.1 Hz
  • Moving mass: 19.2 g
  • Compliance: 20 µm/mN at 10 Hz
  • Cartridge: 7.2 g

A natural starting point, but the data is patchy: the resonance looks fine because the RB330 with 11 g effective mass (manufacturer figure) and the 7.2 g cartridge land just above the lower limit of 8 Hz. Two points that matter just as much in practice stay open, though: Rega gives no weight range for the counterweight and no explicit mounting statement for third-party cartridges. Instead of guessing a “fits”, the calculation therefore reports the overall result as “not verifiable”.

Resonance band: Ortofon 2M Red on Rega Planar 3 Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 8.1 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 8.1 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz).

The calculation in detail

Three points decide whether a cartridge fits a tonearm: the mounting, the resonance of arm and cartridge, and the counterweight. The overall verdict is as strict as the weakest point.

  • Mountingnot verifiable

    Rega names neither the half-inch standard nor an adapter for the arm. According to Rega’s accessory page third-party cartridges can be mounted, but an explicit assurance for half-inch cartridges is missing.

    Advisor output: Rega arm (3-point mounting): Rega names neither the half-inch standard nor an adapter; third-party cartridges can be mounted according to Rega’s accessory page (height: possibly a 2 mm spacer), an adapter is not documented. Counterweight weight range n/a – not verifiable.

  • Resonancefits

    The calculated resonance of 8.1 Hz lies in the target zone of 8–12 Hz.

    Advisor output: fᵣ ≈ 8.1 Hz by 159 / √(19.2 × 20); target 8–12 Hz, warning outside 7–14 Hz. Mass 11 g arm + 7.2 g cartridge + 1 g screws = 19.2 g; compliance 20 µm/mN (10 Hz, per data sheet). Calculation note, not a measurement.

  • Counterweightnot verifiable

    No weight range is documented for this arm’s counterweight; the cartridge weighs 7.2 g.

    Advisor output: Weight range of the arm not documented (n/a) – check the manufacturer’s specification (cartridge 7.2 g).

How the resonance comes about

  1. Moving mass: 11 g arm + 7.2 g cartridge + 1 g screws = 19.2 g.
  2. Compliance at 10 Hz: The compliance of 20 µm/mN is specified at 10 Hz and is used unchanged.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(19.2 × 20) = 159 / √384 ≈ 8.1 Hz.

The input data

Tonearm: Rega RB330 (Rega Planar 3)

Effective mass
11 g · manufacturer figure, source: rega.co.uk
Mounting
Rega three-point mounting (half-inch not explicitly documented)
Counterweight
not documented

Cartridge: Ortofon 2M Red

Type
MM · elliptical bonded (r/R 8/18 µm)
Weight
7.2 g
Compliance
20 µm/mN at 10 Hz
Tracking force
1.6–2.0 g (recommended 1.8 g)
Output voltage
5.5 mV
Market price
about €85–100 (prices without guarantee, Oct 2026)

In our data there is no fixed factory cartridge documented for the Rega Planar 3 (manufacturer: optional from the factory: Rega Nd3 or Nd5 (MM); base unit without cartridge). The calculation applies to a cartridge of your own choice.

What this means for you

  • Ask the manufacturer or a dealer about: Mounting, Counterweight (see the Advisor output above).
  • The resonance alone can be calculated: 8.1 Hz (in the target zone).
  • Without a weight range and a mounting statement we say neither “fits” nor “does not fit”.

The Ortofon 2M Red is a moving-magnet cartridge (5.5 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: Anyone who wants to run the 2M Red with certainty will find the documented variant on the Pro-Ject T2 W: counterweight and mounting are stated in the manufacturer papers there, and the calculation gives 8.5 Hz.

The Ortofon 2M Red on other turntables

On these turntables the Ortofon 2M Red passes all three checks according to the calculation:

Method in brief

Procedure
As in the Advisor: resonance fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Does the Ortofon 2M Red fit the Rega Planar 3?

The available manufacturer data does not allow a final answer. Open: Mounting, Counterweight. Calculated resonance: 8.1 Hz. Orientation only; check the manufacturer’s specifications; errors excepted.

How high is the resonance of the Ortofon 2M Red and the Rega Planar 3?

About 8.1 Hz. The calculation uses 159 / √(mass × compliance): 19.2 g moving mass (arm 11 g, cartridge 7.2 g, screws 1 g) and 20 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the Rega Planar 3 sufficient for the Ortofon 2M Red?

No weight range is documented for this arm’s counterweight; the cartridge weighs 7.2 g. Check the manufacturer’s specification before buying.

What phono input does the Ortofon 2M Red need?

The Ortofon 2M Red is a moving-magnet cartridge (5.5 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet. Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026