Compatibility · Oct 2026
Audio-Technica AT-VM95E on the Rega Planar 3: does it fit?
Checked on paper: the tonearm of the Rega Planar 3 (Rega RB330, 11 g effective mass) with the cartridge Audio-Technica AT-VM95E (6.1 g). The Advisor arrives at 10.5 Hz (range 9.5–11.5 Hz); the verdict is “not verifiable”. Orientation only; check the manufacturer’s specifications; errors excepted.
Verdict: not verifiable
Not verifiable: key data is missing. Checks open: Mounting, Counterweight.
- Resonance: 10.5 Hz (range 9.5–11.5 Hz)
- Moving mass: 18.1 g
- Compliance: 12.6 µm/mN at 10 Hz
- Cartridge: 6.1 g
At 6.1 g the AT-VM95E is clearly lighter than a 2M Red, and its compliance is only specified at 100 Hz. Converting it to 10 Hz is a rule of thumb with a range, but on the RB330 every value lands inside the target zone. As with the 2M Red on the same turntable, the counterweight range of the Rega arm and a documented mount for third-party cartridges are missing, so the overall result stays open.
The calculation in detail
The check runs in three steps: does the cartridge physically fit the arm, does the resonance of arm and cartridge lie in the target zone, and can the counterweight balance the cartridge weight? The weakest point decides the overall verdict.
-
Mountingnot verifiable
Rega names neither the half-inch standard nor an adapter for the arm. According to Rega’s accessory page third-party cartridges can be mounted, but an explicit assurance for half-inch cartridges is missing.
Advisor output: Rega arm (3-point mounting): Rega names neither the half-inch standard nor an adapter; third-party cartridges can be mounted according to Rega’s accessory page (height: possibly a 2 mm spacer), an adapter is not documented. Counterweight weight range n/a – not verifiable.
-
Resonancefits
The calculated resonance of 10.5 Hz lies in the target zone. The rule-of-thumb range stays within the warning limits.
Advisor output: fᵣ ≈ 10.5 Hz (range 9.5–11.5 Hz) by 159 / √(18.1 × 12.6); target 8–12 Hz, warning outside 7–14 Hz. Mass 11 g arm + 6.1 g cartridge + 1 g screws = 18.1 g; compliance 7 ·10⁻⁶ cm/dyn at 100 Hz × 1.5–2.2 ≈ 10.5–15.4 µm/mN at 10 Hz (rule of thumb, middle 12.6). Calculation note, not a measurement.
-
Counterweightnot verifiable
No weight range is documented for this arm’s counterweight; the cartridge weighs 6.1 g.
Advisor output: Weight range of the arm not documented (n/a) – check the manufacturer’s specification (cartridge 6.1 g).
How the resonance comes about
- Moving mass: 11 g arm + 6.1 g cartridge + 1 g screws = 18.1 g.
- Compliance at 10 Hz: The compliance of 7×10⁻⁶ cm/dyn is specified at 100 Hz. For 10 Hz the rule of thumb is 1.5 to 2.2 times that, i.e. 10.5 to 15.4 µm/mN; the calculation uses the middle (factor 1.8): 12.6 µm/mN.
- Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(18.1 × 12.6) = 159 / √228.1 ≈ 10.5 Hz.
- Range: Because the compliance is converted, the result is 9.5–11.5 Hz (worst and best case).
The input data
Tonearm: Rega RB330 (Rega Planar 3)
- Effective mass
- 11 g · manufacturer figure, source: rega.co.uk
- Mounting
- Rega three-point mounting (half-inch not explicitly documented)
- Counterweight
- not documented
Cartridge: Audio-Technica AT-VM95E
- Type
- VM Dual-MM · elliptical bonded 0.3×0.7 mil
- Weight
- 6.1 g
- Compliance
- 7×10⁻⁶ cm/dyn at 100 Hz
- Tracking force
- 1.8–2.2 g · recommended 2.0 g
- Output voltage
- 4 mV
- Market price
- about €55–70 (prices without guarantee, Oct 2026)
In our data there is no fixed factory cartridge documented for the Rega Planar 3 (manufacturer: optional from the factory: Rega Nd3 or Nd5 (MM); base unit without cartridge). The calculation applies to a cartridge of your own choice.
What you can do with this
- Ask the manufacturer or a dealer about: Mounting, Counterweight (see the Advisor output above).
- The resonance alone can be calculated: 10.5 Hz (in the target zone).
- Without a weight range and a mounting statement we say neither “fits” nor “does not fit”.
The Audio-Technica AT-VM95E is a moving-magnet cartridge (4 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
Alternatives
Our tip: The Technics SL-1200GR2 is the documented counter-check for this cartridge: a removable headshell, a counterweight up to 12 g and a resonance of 11.3 Hz with 8.5 g of arm mass.
The Audio-Technica AT-VM95E on other turntables
On paper the Audio-Technica AT-VM95E can also be run on these turntables without objection:
- Pro-Ject T2 W: calculated resonance 11 Hz, arm 9.5 g
- Pro-Ject RPM 5 Carbon: calculated resonance 11.5 Hz, arm 8 g
- Technics SL-1200GR2: calculated resonance 11.3 Hz, arm 8.5 g
- Pro-Ject X8 Evolution: calculated resonance 11.3 Hz, arm 8.5 g
Method in brief
- Procedure
- Same formula as in the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
- Verdict rule
- One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
- Data
- Advisor data of 2 Oct 2026, page of 3 Oct 2026
- Limits
- No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.
Frequently asked questions
Is the Audio-Technica AT-VM95E a good choice for the Rega Planar 3?
The available manufacturer data does not allow a final answer. Open: Mounting, Counterweight. Calculated resonance: 10.5 Hz (range 9.5–11.5 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.
At what frequency do the Audio-Technica AT-VM95E and the arm of the Rega Planar 3 resonate?
About 10.5 Hz (range 9.5–11.5 Hz). The calculation uses 159 / √(mass × compliance): 18.1 g moving mass (arm 11 g, cartridge 6.1 g, screws 1 g) and 12.6 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.
Is the counterweight of the Rega Planar 3 sufficient for the Audio-Technica AT-VM95E?
No weight range is documented for this arm’s counterweight; the cartridge weighs 6.1 g. Check the manufacturer’s specification before buying.
What phono input does the Audio-Technica AT-VM95E need?
The Audio-Technica AT-VM95E is a moving-magnet cartridge (4 mV) and works on a normal MM phono input. If the Rega Planar 3 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
How reliable is this calculation?
It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet, converted with a rule of thumb (factor 1.5–2.2 for 100 Hz values). Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.
Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability
Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026