Compatibility · Oct 2026

Sumiko Rainier on the SME Model 6: does it fit?

We worked through the tonearm of the SME Model 6 (SME M2-9, 9.5 g effective mass) and the cartridge Sumiko Rainier (6.5 g) with the calculation method of our Advisor. Result: fits, calculated resonance 9.1 Hz (range 8.2–10 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.

Verdict: fits Resonance 9.1 Hz Orientation · errors excepted Updated 3 Oct 2026

Verdict: fits

Fits according to our calculation. All three checks (mounting, resonance, counterweight) pass.

  • Resonance: 9.1 Hz (range 8.2–10 Hz)
  • Moving mass: 17 g
  • Compliance: 18 µm/mN at 10 Hz
  • Cartridge: 6.5 g

On the SME Model 6 the M2-9 arm has 9.5 g effective mass and, according to SME, a cartridge balance range of 5 to 12 g. The Sumiko Rainier (6.5 g) sits comfortably inside, the half-inch mount of the removable headshell is documented, and the resonance reaches about 9.1 Hz. Our data documents no factory cartridge for the SME; this combination stays unremarkable in the calculation.

Resonance band: Sumiko Rainier on SME Model 6 Scale 5 to 15 Hz. Target zone 8 to 12 Hz, warning outside 7 to 14 Hz. Calculated resonance 9.1 Hz, range 8.2 to 10 Hz. 5 6 7 8 9 10 11 12 13 14 15 Resonance frequency in Hz Target 8–12 Warning from 7 to 14 9.1 Hz
Calculated resonance compared with the target zone (green: 8–12 Hz) and the warning zone (yellow: 7–14 Hz). The grey bar shows the rule-of-thumb range.

The calculation in detail

Three points decide whether a cartridge fits a tonearm: the mounting, the resonance of arm and cartridge, and the counterweight. The overall verdict is as strict as the weakest point.

  • Mountingfits

    The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.

    Advisor output: Removable headshell with half-inch mount (manufacturer).

  • Resonancefits

    The calculated resonance of 9.1 Hz lies in the target zone. The rule-of-thumb range stays within the warning limits.

    Advisor output: fᵣ ≈ 9.1 Hz (range 8.2–10 Hz) by 159 / √(17 × 18); target 8–12 Hz, warning outside 7–14 Hz. Mass 9.5 g arm + 6.5 g cartridge + 1 g screws = 17 g; compliance 10 ·10⁻⁶ cm/dyn at 100 Hz × 1.5–2.2 ≈ 15–22 µm/mN at 10 Hz (rule of thumb, middle 18). Calculation note, not a measurement.

  • Counterweightfits

    The arm’s counterweight covers the cartridge: 6.5 g lies within the range 5–12 g.

    Advisor output: Cartridge 6.5 g is within the range 5–12 g (cartridge weight (SME: cartridge balance range 5–12 g)).

How the resonance comes about

  1. Moving mass: 9.5 g arm + 6.5 g cartridge + 1 g screws = 17 g.
  2. Compliance at 10 Hz: The compliance of 10×10⁻⁶ cm/dyn is specified at 100 Hz. For 10 Hz the rule of thumb is 1.5 to 2.2 times that, i.e. 15 to 22 µm/mN; the calculation uses the middle (factor 1.8): 18 µm/mN.
  3. Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(17 × 18) = 159 / √306 ≈ 9.1 Hz.
  4. Range: Because the compliance is converted, the result is 8.2–10 Hz (worst and best case).

The input data

Tonearm: SME M2-9 (SME Model 6)

Effective mass
9.5 g · manufacturer figure, source: sme.co.uk
Mounting
removable headshell, half-inch mount
Counterweight
5–12 g · cartridge weight (SME: cartridge balance range 5–12 g)

Cartridge: Sumiko Rainier

Type
MM · elliptical · alloy tube
Weight
6.5 g
Compliance
10×10⁻⁶ cm/dyn at 100 Hz
Tracking force
1.8–2.2 g · recommended 2.0 g
Output voltage
5 mV
Market price
about €140–170 (prices without guarantee, Oct 2026)

In our data there is no fixed factory cartridge documented for the SME Model 6. The calculation applies to a cartridge of your own choice.

What this means for you

  • Set the tracking force as specified by the manufacturer (1.8–2.2 g · recommended 2.0 g) and check it with a gauge.
  • Set the overhang with the alignment protractor, then the anti-skating.
  • Compare the manufacturer’s specifications for arm and cartridge before you order or mount.

The Sumiko Rainier is a moving-magnet cartridge (5 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

Alternatives

Our tip: One price class higher is the Audio-Technica AT-VM95ML (about €150–190): 6.1 g and 9.2 Hz on the SME arm.

More cartridges on the SME Model 6

If you would like to compare: these cartridges also pass all three checks on the SME Model 6 and cost roughly the same according to our test pages (prices without guarantee):

The Sumiko Rainier on other turntables

On these turntables the Sumiko Rainier passes all three checks according to the calculation:

Method in brief

Procedure
As in the Advisor: resonance fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
Verdict rule
One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
Data
Advisor data of 2 Oct 2026, page of 3 Oct 2026
Limits
No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.

Frequently asked questions

Does the Sumiko Rainier fit the SME Model 6?

Yes, according to our calculation the Sumiko Rainier fits the SME Model 6: mounting, resonance and counterweight pass. Calculated resonance: 9.1 Hz (range 8.2–10 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.

How high is the resonance of the Sumiko Rainier and the SME Model 6?

About 9.1 Hz (range 8.2–10 Hz). The calculation uses 159 / √(mass × compliance): 17 g moving mass (arm 9.5 g, cartridge 6.5 g, screws 1 g) and 18 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.

Is the counterweight of the SME Model 6 sufficient for the Sumiko Rainier?

The arm’s counterweight covers the cartridge: 6.5 g lies within the range 5–12 g.

What phono input does the Sumiko Rainier need?

The Sumiko Rainier is a moving-magnet cartridge (5 mV) and works on a normal MM phono input. If the SME Model 6 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.

How reliable is this calculation?

It is an orientation, not a measurement. The arm mass comes from a manufacturer figure, the compliance from the manufacturer’s data sheet, converted with a rule of thumb (factor 1.5–2.2 for 100 Hz values). Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.

Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability

Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026