Compatibility · Oct 2026
Audio-Technica AT-VM95E on the Thorens TD 202: does it fit?
Checked on paper: the tonearm of the Thorens TD 202 (Thorens TP 71, 14 g effective mass) with the cartridge Audio-Technica AT-VM95E (6.1 g). The Advisor arrives at 9.8 Hz (range 8.8–10.7 Hz); the verdict is “does not fit”. Orientation only; check the manufacturer’s specifications; errors excepted.
Verdict: does not fit
Does not fit: one point is clearly outside. Checks outside: Counterweight.
- Resonance: 9.8 Hz (range 8.8–10.7 Hz)
- Moving mass: 21.1 g
- Compliance: 12.6 µm/mN at 10 Hz
- Cartridge: 6.1 g
A matter of tenths of a gram: per the Thorens data sheet the TD 202’s counterweight is designed for cartridges up to 6.0 g, and the AT-VM95E weighs 6.1 g. The resonance of about 9.8 Hz would be perfectly unremarkable. Thorens ships the AT-95E, a different model from the VM95E. The calculation applies the upper limit strictly and reports “does not fit”; a look at the manufacturer’s specification is worthwhile before ruling the combination out.
The calculation in detail
The check runs in three steps: does the cartridge physically fit the arm, does the resonance of arm and cartridge lie in the target zone, and can the counterweight balance the cartridge weight? The weakest point decides the overall verdict.
-
Mountingfits
The cartridge has the usual half-inch mounting (two screws, hole spacing ½ inch), and the arm’s headshell is designed for it.
Advisor output: Removable headshell; half-inch standard (assumption for standard cartridges, source Wikipedia “Tonearm”).
-
Resonancefits
The calculated resonance of 9.8 Hz lies in the target zone. The rule-of-thumb range stays within the warning limits.
Advisor output: fᵣ ≈ 9.8 Hz (range 8.8–10.7 Hz) by 159 / √(21.1 × 12.6); target 8–12 Hz, warning outside 7–14 Hz. Mass 14 g arm + 6.1 g cartridge + 1 g screws = 21.1 g; compliance 7 ·10⁻⁶ cm/dyn at 100 Hz × 1.5–2.2 ≈ 10.5–15.4 µm/mN at 10 Hz (rule of thumb, middle 12.6). Calculation note, not a measurement.
-
Counterweightdoes not fit
The cartridge (6.1 g) is heavier than the upper limit of 6 g. The counterweight is not sufficient for balance.
Advisor output: Cartridge 6.1 g outside the range 3.5–6 g (cartridge weight (Thorens data sheet: 3.5–6.0 g)).
How the resonance comes about
- Moving mass: 14 g arm + 6.1 g cartridge + 1 g screws = 21.1 g.
- Compliance at 10 Hz: The compliance of 7×10⁻⁶ cm/dyn is specified at 100 Hz. For 10 Hz the rule of thumb is 1.5 to 2.2 times that, i.e. 10.5 to 15.4 µm/mN; the calculation uses the middle (factor 1.8): 12.6 µm/mN.
- Formula: fᵣ = 159 / √(mass × compliance) = 159 / √(21.1 × 12.6) = 159 / √265.9 ≈ 9.8 Hz.
- Range: Because the compliance is converted, the result is 8.8–10.7 Hz (worst and best case).
The input data
Tonearm: Thorens TP 71 (Thorens TD 202)
- Effective mass
- 14 g · lab measurement by a trade magazine (not a manufacturer value), source: hifinews.com
- Mounting
- removable headshell
- Counterweight
- 3.5–6 g · cartridge weight (Thorens data sheet: 3.5–6.0 g)
Cartridge: Audio-Technica AT-VM95E
- Type
- VM Dual-MM · elliptical bonded 0.3×0.7 mil
- Weight
- 6.1 g
- Compliance
- 7×10⁻⁶ cm/dyn at 100 Hz
- Tracking force
- 1.8–2.2 g · recommended 2.0 g
- Output voltage
- 4 mV
- Market price
- about €55–70 (prices without guarantee, Oct 2026)
According to the manufacturer the Thorens TD 202 ships with a different cartridge (Audio-Technica AT-95E (MM)). The calculation here therefore describes a swap, i.e. an upgrade scenario.
What you can do with this
- Based on the calculation we advise against this combination; decisive: Counterweight.
- Choose a cartridge within the arm’s weight range (see the alternatives below).
- Check the manufacturer’s specification if you suspect an exception; the calculation is no substitute for the manufacturer’s approval.
The Audio-Technica AT-VM95E is a moving-magnet cartridge (4 mV) and works on a normal MM phono input. If the Thorens TD 202 has no built-in phono stage or the amplifier has no phono input, the top list of phono preamps helps.
Alternatives
Our tip: On the Pro-Ject T2 W 9.5 g of arm mass and a counterweight up to 11.5 g are documented; the cartridge calculates to 11 Hz there.
The Audio-Technica AT-VM95E on other turntables
On paper the Audio-Technica AT-VM95E can also be run on these turntables without objection:
- Pro-Ject T2 W: calculated resonance 11 Hz, arm 9.5 g
- Pro-Ject RPM 5 Carbon: calculated resonance 11.5 Hz, arm 8 g
- Technics SL-1200GR2: calculated resonance 11.3 Hz, arm 8.5 g
- Pro-Ject Primary E: calculated resonance 11.5 Hz, arm 8 g
Method in brief
- Procedure
- Same formula as in the Advisor: fᵣ = 159 / √(mass × compliance), target 8–12 Hz, warning outside 7–14 Hz. Mass = arm mass + cartridge weight + 1 g screws. 100 Hz values are converted with 1.5–2.2.
- Verdict rule
- One point outside: “does not fit”. Mounting or resonance not verifiable: “not verifiable”. One point at the edge: “borderline”. Otherwise “fits”.
- Data
- Advisor data of 2 Oct 2026, page of 3 Oct 2026
- Limits
- No measurement, no guarantee. Orientation only; check the manufacturer’s specifications; errors excepted.
Frequently asked questions
Is the Audio-Technica AT-VM95E a good choice for the Thorens TD 202?
Not according to our calculation. The Audio-Technica AT-VM95E on the Thorens TD 202 fails on Counterweight. Calculated resonance: 9.8 Hz (range 8.8–10.7 Hz). Orientation only; check the manufacturer’s specifications; errors excepted.
At what frequency do the Audio-Technica AT-VM95E and the arm of the Thorens TD 202 resonate?
About 9.8 Hz (range 8.8–10.7 Hz). The calculation uses 159 / √(mass × compliance): 21.1 g moving mass (arm 14 g, cartridge 6.1 g, screws 1 g) and 12.6 µm/mN at 10 Hz. The target zone is 8–12 Hz; a warning applies outside 7–14 Hz.
Is the counterweight of the Thorens TD 202 sufficient for the Audio-Technica AT-VM95E?
The cartridge (6.1 g) is heavier than the upper limit of 6 g. The counterweight is not sufficient for balance. Check the manufacturer’s specification before buying.
What is fitted to the Thorens TD 202 at the factory?
According to the manufacturer the Thorens TD 202 ships with a different cartridge (Audio-Technica AT-95E (MM)). The calculation here therefore describes a swap, i.e. an upgrade scenario.
How reliable is this calculation?
It is an orientation, not a measurement. The arm mass comes from a lab measurement by a trade magazine (not a manufacturer value), the compliance from the manufacturer’s data sheet, converted with a rule of thumb (factor 1.5–2.2 for 100 Hz values). Data as of 2 Oct 2026. Check the manufacturer’s specifications; errors excepted.
Orientation only; check the manufacturer’s specifications; errors excepted. Calculation by the AI Vinyl BotPro based on manufacturer data, without listening test and without measurement, not purchase advice in the legal sense. Notices & liability
Updated 3 Oct 2026 · Advisor data 2 Oct 2026 · Prices without guarantee, Oct 2026