Phono preamp · AI analysis · Master, rank 6

Luxman EQ-500: Analysis

AI analysis (research): all-tube CR equaliser with MC transformers and front-panel adjustment — specifications and MSRP, no listening test.

AI research Master Index 92 / 100 Price as of Sept 2026
Luxman EQ-500, phono preamp
Photo: manufacturer Luxman · product photo for illustration only.
Luxman EQ-500 (2/3) — manufacturer photo
Photo: manufacturer Luxman · additional product photo.
Luxman EQ-500 (3/3) — manufacturer photo
Photo: manufacturer Luxman · additional product photo.

Summary

Sound Vinyl BotPro Champion: Luxman EQ-500, Master, Vinyl BotPro Index 92, Analysis 09/2026. AI assessment of the expected sound data, not a listening test.VinylCinationLevelMasterLuxman EQ-500Phono preamp92Vinyl BotPro IndexSoundVinyl BotPro ChampionAnalysis (09/2026)www.VinylCination.de

The EQ-500 is Luxman's all-tube phono stage: SRPP + cathode follower, CR EQ (non-feedback), MC SUT High/Low, gain MM 36 / MC High 55 / MC Low 63 dB (at gain setting 36 dB), MM load 30–100 kΩ variable, switchable capacitance, Articulator, mono, low/high cut, XLR+RCA out. MSRP often ~€7,000. Press consensus musical/harmonic — Sound champion; overall winner remains C-47.

Assumptions

  • Tube maintenance / JJ assembly
  • Optionally available new equipment EN
  • No measurements of our own

Specs (public / manufacturer)

TypeMM/MC Phono · Full tube · CR-EQ non-feedback
Gain (at 36 dB position)MM 36 · MC High 55 · MC Low 63 dB
Load (MM)30–100 kΩ variable · C 0–300 pF switchable
Load (MC)High 40 Ω · Low 2.5 Ω (SUT)
TubeAll-tube (tube types not specified by manufacturer)
I/O3× RCA Phono In · 2× RCA + 1× XLR Out
Price guideMSRP often ~€6,990–7,000 · Sept 2026 · Check the price date
Manufacturer specifications (Luxman)
Manufacturer data sheet
Typeall-tube phono preamp, MC step-up transformers
Gain factorMM 36 dB · MC high 55 dB · MC low 63 dB (36 dB setting)
Input impedance/capacitanceMM 30–100 kΩ variable · MC high 40 Ω · MC low 2.5 Ω · capacitance 0/50/100/150/200/300 pF
Input sensitivityMM 4 mV · MC high 0.44 mV · MC low 0.18 mV
Max. input levelMM 300 mV · MC high 34 mV · MC low 13 mV
RIAA accuracy±0.3 dB (20 Hz–20 kHz)
Outputs250 mV / 850 Ω
Power consumption47 W
Dimensions440 × 92 × 397 mm (W × H × D)
Weight12.5 kg

Source: Luxman – official specifications · As of 16 October 2026 · subject to change by the manufacturer

Scores in detail

Technology / build
Full tube · SUT · CR-EQ · Luxman construction
9.2
Features
Front alignment · Articulator · Curve filter
9.1
Expected performance
Press consensus: strong sound focus
9.4
Value for money
Fair in the upper master's centre
7.0
Total
Vinyl BotPro Index 92
9.0

Vinyl BotPro Index: 92 · Index band Master 85–97 · Guidance only, not a lab value.

Strengths

  • Full tube with front control
  • MC-SUT High/Low
  • Articulator / Mono / Filter

Weaknesses

  • Tube change
  • Optionally available
  • No Balanced-In

Comparison models

Nagra Classic PhonoMore expensive, Teldec/Columbia
Rega Aura MCSolid-State MC-only
Allnic H-5500Other tube school ~6k €

System matching

Works well with

  • MM and Low-MC with SUT
  • Tube amps
  • Who seeks musical consensus

Less suited

  • Maintenance-free Solid-State-only
  • Budget below €3,000

Created by Vinyl BotPro (AI) · As of Sept 2026 · Corrections: info@vinylcination.de

Manufacturer and concept

Luxman is one of Japan's oldest hi-fi manufacturers, known for valve equipment, large analogue meters and a distinctive design language. The EQ-500 was launched in April 2015 and is the phono stage at the top of its range. It follows a clear idea: an all-valve equalisation stage, combined with built-in MC step-up transformers and so many front-panel adjustments that several turntables and cartridges can be run from one unit.

The EQ-500 is therefore not aimed at listeners who want a small box hidden behind the rack, but at collectors with several tonearms who like to make adjustments while listening. At 440 × 92 × 397 mm and 12.5 kg it is the size of an integrated amplifier.

Why valves in a phono stage at all? Valves amplify with a different distortion profile than transistors: as they approach their limits they mainly produce low-order harmonics and clip more softly. Many listeners associate this with a rounded, colourful presentation. The downside is a higher noise floor, which matters especially with the tiny voltages of MC cartridges. Luxman solves this with built-in transformers that raise the signal without adding noise before the first valve handles it.

Technology explained

CR equalisation without feedback

Every phono stage has to reverse the RIAA curve used to cut records: bass is boosted and treble cut. Many circuits do this in an amplifier's feedback loop. In the EQ-500 Luxman uses CR equalisation – a passive network of capacitors and resistors between two amplifier stages – with no feedback around the equalisation. Luxman specifies RIAA accuracy of ±0.3 dB from 20 Hz to 20 kHz.

Valve stages and MC transformers

All gain stages use valves. For MC cartridges there are four transformers inside, one each left and right for the “MC High” input (40 Ω) and for “MC Low” (2.5 Ω). A transformer passively steps up the very small voltage of an MC cartridge before the valves take over – a classic way to achieve low noise with valve circuits. Luxman quotes gain of 36 dB for MM, 55 dB for MC High and 63 dB for MC Low at the base setting.

Matching the cartridge

For MM cartridges the input resistance is continuously adjustable from 30 to 100 kΩ, and capacitance can be set in six steps from 0 to 300 pF, so the treble response of an MM cartridge can be tailored. There are also a mono switch, low- and high-cut filters and a cartridge demagnetising function. Three phono inputs accept three tonearms at once; outputs are two pairs of RCA and one XLR.

The data sheet in context

Input sensitivity is the voltage the cartridge must deliver for the rated 250 mV output. Luxman gives 4 mV for MM, 0.44 mV for MC High and 0.18 mV for MC Low. A typical MM cartridge with 4 to 5 mV fits exactly, an MC with 0.4 to 0.5 mV belongs on MC High, very quiet cartridges with 0.2 to 0.3 mV on MC Low. Maximum input – 300 mV for MM, 34 mV for MC High and 13 mV for MC Low – is far above what a cartridge delivers even in loud passages. This overload margin matters because clicks and hot cuts can briefly produce many times the nominal level.

The 250 mV output at 850 Ω is typical for a valve stage and suits the line inputs of most preamplifiers; for very long cables or power amplifiers with low input impedance, the XLR output or a short RCA run is preferable.

Sound according to international reviews

Art Dudley reviewed the EQ-500 at length for Stereophile in April 2016. His first impression was reserved; after a longer run-in he described it as one of the best-sounding, most musical phono preamps he had had in his system, praising fine detail against a very quiet background, tonal colour, force and deep bass. As a limitation he noted that there are no alternative equalisation curves for 78s or early US pressings.

Tom Mathew reported extraordinary detail retrieval, a lush midrange and an immense soundstage for SoundStage! Ultra in July 2016. It also warned that the many settings require patience and that the brief manual assumes experience; the EQ-500 should not be a first phono stage, but could well be the last. We do not run our own listening tests.

Features and practice

In daily use the EQ-500 is a tool for people who enjoy adjusting. Load and capacitance are selected on the front, so differences can be compared without reaching behind the unit. Two meters show the level. After switch-on the output stays silent because of a timed mute; the manual requires a well-ventilated place out of direct sun. Dudley and What Hi-Fi? describe the case as only warm, not hot; after many years a valve change is due. Luxman specifies 47 W power consumption – a lot for a device that handles a signal of a few millivolts, a result of valve heating and generously sized power supplies.

There is no balanced phono input; anyone wanting to wire the tonearm balanced is better served by the Accuphase C-47. The XLR output, on the other hand, makes connection to balanced preamplifiers easy.

Which input for which cartridge?

As a rule of thumb: MM and MI cartridges as well as high-output MC on the MM input with 47 kΩ as a starting point; MC cartridges with around 10 to 40 Ω coil impedance on MC High; very low-impedance MCs of a few ohms on MC Low. A low-output MC such as the Lyra Delos with 6.3 Ω and 0.6 mV sits between the two transformers, so a direct comparison is worthwhile. With MM cartridges, capacitance affects the treble: the total of tonearm cable and input should be in the range the cartridge maker specifies.

Placement

Valves are sensitive to vibration and produce heat. The EQ-500 belongs on a stable shelf with space above, not directly on a power amplifier. Nearby mains transformers can induce hum; half a metre from large power amps is a sensible starting point. Turntable ground leads go to the three separate ground terminals. If hum persists, a different cable route or reversing the mains plug often helps; short, well-shielded, low-capacitance RCA phono leads are sufficient.

Who it suits

The EQ-500 suits collectors with several turntables or tonearms, owners of MM and low-output MC cartridges, and listeners who deliberately want a valve presentation. For a single turntable with a fixed cartridge it is oversized. Anyone wanting a maintenance-free unit without valves should choose a transistor phono stage.

Comparison with alternatives

All models with index and price are listed in our best phono preamps.

Analysis: the Luxman EQ-500 in depth

Scope and sources

This analysis adds manufacturer data, laboratory measurements and the judgements of ten sources to the overview above. It was compiled by Vinyl BotPro from the sources listed below; there were no listening tests or measurements of our own. Where we calculate a figure ourselves, that is stated. The basis is Luxman's English and Japanese product pages [1][2], the owner's manual [3], PHILE WEB's launch report of 13 March 2015 [4], Stereophile's listening report and laboratory measurements [5][6], and listening reports from SoundStage! Ultra, What Hi-Fi?, HiFi Live and TONE [7][8][9][10].

We did not find a review in an independent German specialist publication. The page therefore rests on the manufacturer's figures and on the international specialist press.

Launch in 2015 and its place in the range

PHILE WEB announced the EQ-500 on 13 March 2015: Japanese sale from late April 2015, then 500,000 yen excluding tax, in Blaster White [4]. The Japanese product page gives April 2015 as the launch month and confirms that list price; in November 2022 the price was raised to 530,000 yen excluding tax [2]. PHILE WEB places the unit as the first new model of Luxman's 90th anniversary year [4]. Luxman itself traces the circuit to the E-06 CR equaliser of the 1980s, reworked here with valves in every gain stage [1][2]. On the current Japanese and international product pages the EQ-500 remains the company's flagship valve phono stage [1][2].

Circuit and construction

Every gain stage uses valves. The first and second stages are SRPP (shunt-regulated push-pull), the final stage a paralleled cathode follower; equalisation is a passive CR network without feedback between the stages [1][2][3]. Luxman specifies the complement officially: four ECC83, two ECC82 and one EZ81, all from JJ Electronic in Slovakia, in gold-plated ceramic sockets [1][2][3]. The EZ81 works as a rectifier valve together with a choke in the power supply [1][3]. The specification table already on this page says the manufacturer does not state the valve types – that is not correct.

For MC cartridges there are four transformers in the unit, not two: a Super Permalloy transformer each for MC High and MC Low, separate for left and right [1][2][3]. A further Super Permalloy transformer sits in the output and also serves the balanced output [1][3]. Coupling capacitors are by Mundorf, internal wiring is OFC; the chassis is a loop-less design with heavy shielding of the power supply and equaliser sections [1][2][4]. Art Dudley counted 19 relays on the audio board for the switching functions and described a lacquered copper plate covering the audio circuit [5]. What Hi-Fi? and SoundStage! Ultra confirm the seven valves and the extensive shielding [7][8].

The case, at 440 × 92 × 397 mm, is deliberately shallow so that it can sit on a preamplifier; the 397 mm depth includes 5 mm front knobs and 12 mm rear sockets [1][2][3]. The unit weighs 12.5 kg, 15.2 kg packed [2]. The front panel is Blaster White, with two meters whose sensitivity can be switched and which can also be turned off [1][3].

Manufacturer data and what it means

All gain figures in the tables apply with the gain switch at 36 dB: 36 dB for MM, 55 dB for MC High and 63 dB for MC Low [1][2][3]. The switch itself offers 36, 38 and 40 dB [3][4]. Our own calculation: at the 40 dB setting that becomes 40 dB (MM), 59 dB (MC High) and 67 dB (MC Low). John Atkinson quoted specified MC gains of 55 and 67 dB [6]; the 67 dB figure matches the 40 dB setting, not the 36 dB setting printed in the tables.

Input sensitivity for 250 mV output is 4 mV (MM), 0.44 mV (MC High) and 0.18 mV (MC Low) [1][2][3]. Our own calculation: 4 mV times 10 to the power of (36/20) is about 252 mV, 0.44 mV times 10 to the power of (55/20) about 247 mV, 0.18 mV times 10 to the power of (63/20) about 254 mV. The three pairs therefore match the rated gain. Maximum input at 1 kHz is 300 mV, 34 mV and 13 mV [1][3]. Our own calculation: relative to the rated sensitivities that is about 37.5 dB, 37.8 dB and 37.2 dB of margin at 1 kHz.

Luxman specifies RIAA accuracy of ±0.3 dB from 20 Hz to 20 kHz, output of 250 mV into 850 Ω, and channel separation of 65 dB at 10 kHz [1][2][3]. Two figures appear only on the Japanese product page and in the owner's manual, not on the international page: total harmonic distortion of 0.07% (1 kHz, 1 V output, gain 36 dB) and signal-to-noise ratio (IHF-A, gain 36 dB) of 76 dB (MM), 75 dB (MC High) and 74 dB (MC Low) [2][3]. Power consumption is 47 W [1][2][3].

MM load is continuously variable from 30 to 100 kΩ, capacitance in six steps from 0 to 300 pF; MC High is fixed at 40 Ω, MC Low at 2.5 Ω [1][3]. TONE wrote of 10 kΩ to 100 kΩ [10]; we follow the manufacturer and the manual, which give 30 kΩ as the lower limit.

Stereophile's measurements

John Atkinson measured the EQ-500 in April 2016 with an Audio Precision SYS2722 [6]. On MM he measured 36.4, 38.4 and 40.5 dB in the three gain settings – very close to 36, 38 and 40 dB [6]. On MC the analyser output impedance of 20 Ω distorted the raw figures, because the transformer input impedances of 56 Ω (High) and 7 Ω (Low) are low; after correcting for the voltage divider he obtained 58.6 and 68.2 dB, close to the specified 55 and 67 dB he quoted [6]. In other words he measured slightly more gain than specified.

The set MM impedance was not met exactly: at 47 kΩ he measured 37 kΩ at 20 Hz and 29 kΩ at 20 kHz, at 100 kΩ 78 to 55 kΩ, at 30 kΩ 30 to 24 kΩ, all with capacitance at 0 pF [6]. Output impedance was close to the specified 850 Ω: unbalanced 880 Ω at 20 Hz and 812 Ω from 1 kHz up, balanced 983 Ω at the bottom of the band and 910 Ω above [6]. The RCA and XLR outputs delivered the same level; with the Phase switch at Normal, absolute polarity was preserved at the RCA outputs but inverted at the XLR sockets, which are wired pin 3 hot – the older standard, not the current AES/EIA convention of pin 2 hot [6]. The block diagram in the owner's manual marks pin 2 as COLD and pin 3 as HOT [3].

The RIAA curve followed the target very closely, with the two channels superimposed [6]. Channel separation was almost 90 dB below 1 kHz and still 63 dB at 20 kHz [6], which fits the specified 65 dB at 10 kHz [1][3]. Unweighted signal-to-noise (MM, ref. 5 mV, inputs shorted) was 59 dB left and 65 dB right, A-weighted 77.2 and 78.5 dB [6] – close to the official 76 dB IHF-A [2][3]. Noise stayed almost the same on the MC settings, which Atkinson attributes to the transformers [6]. Power-supply spuriae were almost absent [6].

The MM overload margin at 1 kHz was excellent at 30 dB ref. 5 mV, but fell at the frequency extremes to 15 dB at 20 Hz and 12 dB at 20 kHz [6]. Harmonic distortion was typically 0.05%, mainly the second harmonic at −67 dB; into 600 Ω the second harmonic rose sharply, a load the stage will not see in normal use [6]. Intermodulation from 19 and 20 kHz tones sat at −47 dB left and −50 dB right, a little higher than Atkinson would have liked, with higher-order products much lower [6]. He concluded that it was a pleasure to measure and that the design was good, solid audio engineering [6].

Filters, polarity and the XLR output

The owner's manual describes the High Cut as a filter above 8 kHz at −6 dB per octave (a scratch filter) and the Low Cut as a filter below 20 Hz at −6 dB per octave, intended to reduce cone flap with warped records [3]. Atkinson measured the High Cut at −6 dB at 10 kHz and the Low Cut at −6 dB at 10 Hz [6]. The figures describe the same filter type from different points on the curve; the manual gives 8 kHz and 20 Hz as the corner frequencies. SoundStage! Ultra found the treble filter useful on older, well-played records: it softened and cleaned the sound without sounding artificial [7]. TONE also mentions the filters as a help with 78s and poor pressings [10] – they do not, however, replace alternative equalisation curves.

An important connection point: the Output switch selects either the two RCA outputs or the XLR output. With UNBAL selected there is no signal at the XLR sockets; with BAL selected the RCA sockets are silent [3]. Add the pin-3-hot wiring already described [3][6]. A cable wired to AES/EIA (pin 2 hot) will invert polarity at the XLR output, which can be corrected with the front-panel Phase switch [3][6].

Sound according to the specialist press

The listening reports agree in direction but differ in tone. Art Dudley's first session was reserved: less bass and mid-bass than his combination of Hommage T2 transformer and Shindo Masseto phono section, a smaller soundstage, and a somewhat artificial spit on alto saxophone [5]. After a few hours with the unit left on he described a clear change: force and attack, believable timbre, greater image depth, fine detail against a very quiet background; he called the EQ-500 one of the best-sounding, most musical phono preamps he had had in his system, and a must-hear if the budget will stretch [5]. As a limitation he noted the absence of curves for 78s and early US Columbia pressings [5].

Tom Mathew, writing for SoundStage! Ultra on 1 July 2016, reported extraordinary detail retrieval, a typically lovely Luxman midrange, an immense soundstage, a voluptuous but controlled valve sound, powerful bass and a vanishingly low noise floor [7]. The unit already sounded good out of the box and became luminous after about 100 hours; even months later he was still hearing small improvements [7]. He warned that the many combinations of settings and valve gain require patience and that the brief manual assumes experience: the EQ-500 should not be your first phono stage, though it could well be your last [7]. The list price in his report was 7,490 US dollars [7].

What Hi-Fi? listened to the stage on 20 April 2017 at a then price of 5,000 pounds and advised against judging it too quickly: just after switch-on it sounded thick and a little timid; once the valve circuit had stabilised it gained transparency and openness, and the casework hardly got warm [8]. The first thing that struck the reviewers was how quiet it was, with very low background hiss [8]. They then described sure-footed rhythm and punch, a stable, expansive stage and a very high level of detail presented in an unforced way; the tonal rounding was not taken too far [8]. The recommendation comes with the caveat that the stage demands a first-class system [8].

David Mallen heard the EQ-500 for the Spanish magazine HiFi Live (published 23 September 2016) and put the emphasis on neutrality, cleanliness and transparency, a deep soundstage that did not inflate size, and versatile controls; the unit stayed quiet even at high listening levels [9]. Compared with his Trinity reference, the Luxman did not quite reach the same last degree of perfection but offered much more adjustability [9]. Jeff Dorgay, writing for TONE in October 2019, described the EQ-500 as organic, inviting, slightly warm and relaxed, resolving but never fatiguing, and quieter than some much more expensive valve stages [10]. Dynamic reserve and grip on the deepest bass notes did not quite match five-figure units such as the Audio Research Reference Phono 3 or the BAT VK-P12SE; even so, he placed it close to the dearer Nagra VPS, especially given the three inputs [10].

Comparisons in the reports

Dudley compared the built-in transformers with his Hommage T2 on an EMT TSD 15: the external transformer gave a richer piano bass, more depth on electric bass and bass drum, and a larger sense of scale – from a unit designed specifically for that cartridge and costly in its own right [5]. With a Shindo SPU straight into the MC Low input and gain at 40 dB, the EQ-500 was, for him, on a par with the EMT-plus-Hommage combination [5]. He used high-output MC cartridges such as the EMT OFD mono pickups on MC High at 36 dB; the Mono switch worked correctly even when the cartridge carries signal on only one channel [5].

TONE placed the EQ-500 at 6,495 US dollars beside the Audio Research PH9 at the same price, which offers only one input and a single gain setting, and beside the much dearer Nagra VPS [10]. HiFi Live quoted 6,990 euros [9]. What Hi-Fi? stressed that without a matching source, amplification and loudspeakers the stage would not be heard at its best [8].

Matching the cartridge

All the main adjustments are on the front panel [1][3][10]. MM and MI cartridges, and many high-output MCs, belong on the MM input, typically starting at 47 kΩ – Dudley notes that this value sits at 12 o'clock on the impedance knob [5]. Capacitance, together with the tonearm cable, should fall in the range given by the cartridge manufacturer [3]. MC cartridges with higher coil impedance belong on MC High (40 Ω), very low-impedance types on MC Low (2.5 Ω); the manual refers users to the cartridge maker's figures [3]. TONE considers even very low-output cartridges usable in most cases [10]. Three RCA inputs and three separate ground terminals allow three tonearms; TONE singles out the separate grounds and mentions the blanking plugs supplied for unused sockets [3][10].

Articulator, mono and daily use

According to the manual, the Articulator demagnetises the cartridge and the MC transformers using the music signal of the record being played; the output is muted or very quiet, about 30 seconds or until the end of the track is recommended, and the switch should be returned before raising the volume [3]. Dudley followed the 30-second advice and was not sure he heard a difference; at most his EMT TSD 15 seemed a little less grainy [5]. What Hi-Fi? likewise heard little difference in its system [8]. Tom Mathew, by contrast, described more colour and shading from a used Koetsu after demagnetisation [7]. TONE advises doing the procedure with the power amplifier off and repeating it every 100 hours or so [10] – that is the magazine's advice, not a manufacturer specification.

The Mono switch sums both channels [3]. Dudley could thereby send a true mono cartridge correctly to both loudspeakers [5]. SoundStage! Ultra also found the switch a gain on mono mixes [7]. The LINE-1 and LINE-2 outputs are sonically equivalent according to the manual [3].

Placement, heat and valves

After switch-on the output stays silent because of a timed mute circuit; the manual says not to raise the volume until sound appears [3]. For placement it requires a well-ventilated position out of direct sunlight, away from heaters, and not in high humidity or dust [3]. Dudley was surprised that the sealed case gives no hint of the valves inside, but found the unit only warm, not hot, and gave it space around it [5]. What Hi-Fi? also says the casework hardly gets warm, but advises allowing the circuit to stabilise [8]. SoundStage! Ultra observed no unusual heat [7]. The 47 W power consumption comes mainly from the valve heaters and the power supply [1][8]. Luxman does not give a fixed daily warm-up time.

Prices over time

The documented figures are: 500,000 yen excluding tax at launch in 2015 [2][4], 530,000 yen excluding tax from November 2022 [2], 7,490 US dollars in the 2016 Stereophile and SoundStage! Ultra reports [5][7], 6,495 US dollars in TONE in 2019 [10], 5,000 pounds in What Hi-Fi? in 2017 [8], and 6,990 euros in HiFi Live in 2016 [9]. We did not find a current euro list price on the manufacturer's sites. The range often given on this page, about 6,990 to 7,000 euros (as of September 2026), matches the 2016 HiFi Live figure; we do not have an independent current confirmation.

Conclusion of the analysis

The sources portray the EQ-500 as a fully equipped valve phono stage with built-in MC transformers, whose strength lies in the combination of a quiet background, a musical presentation and front-panel control for several cartridges [5][7][8][9][10]. The measurements support the manufacturer's claims for RIAA accuracy and quietness; limitations appear in overload margin at the frequency extremes, in the XLR pin-out, and in MM impedance that does not land exactly on the set value [6]. Several magazines see it as especially well suited to collectors with more than one tonearm [5][7][10]; there are no alternative equalisation curves for 78s and early US pressings [5], there is no balanced phono input, and the valves need maintenance. In our ranking it stands at index 92 as the Sound champion of the Master tier – that is an AI assessment from the available data, not a listening test of our own.

Sources for this analysis

  1. Luxman: EQ-500 – Produktseite mit technischen Daten/product page with specifications (EN, abgerufen/accessed 12.11.2026). https://luxman.com/product/detail.php?id=6
  2. Luxman: EQ-500 – japanische Produktseite mit Einführung April 2015, Preisen und zusätzlichen Messangaben/Japanese product page with April 2015 launch, prices and additional specifications (abgerufen/accessed 12.11.2026). https://www.luxman.co.jp/product/eq-500
  3. Luxman: EQ-500 Owner's Manual / Bedienungsanleitung (PDF, AG00987E26A). https://www.luxman.co.jp/asset/manual/EQ-500_AG00987E26A.pdf
  4. PHILE WEB: ラックスマン、無帰還CR型増幅回路の全段真空管フォノイコアンプ「EQ-500」(News, 編集部:杉浦 みな子 / Minako Sugiura, 13.03.2015). https://www.phileweb.com/news/audio/201503/13/15646.html
  5. Stereophile: Luxman EQ-500 phono preamplifier (Art Dudley, 27.04.2016). https://www.stereophile.com/content/luxman-eq-500-phono-preamplifier
  6. Stereophile: Luxman EQ-500 phono preamplifier Measurements (John Atkinson, 27.04.2016). https://www.stereophile.com/content/luxman-eq-500-phono-preamplifier-measurements
  7. SoundStage! Ultra: Luxman EQ-500 Phono Stage (Tom Mathew, 01.07.2016). https://www.soundstageultra.com/index.php/equipment-menu/659-luxman-eq-500-phono-stage
  8. What Hi-Fi?: Luxman EQ-500 review (20.04.2017, tested at £5000). https://www.whathifi.com/luxman/eq-500/review
  9. HiFi Live: Luxman EQ-500 (David Mallen, 23.09.2016). https://hifilivemagazine.com/luxman-eq-500-3/
  10. TONE: The Luxman EQ-500 (Jeff Dorgay, 24.10.2019). https://tonepublications2.com/project/the-luxman-eq-500/

Created by AI (Vinyl BotPro) from the sources listed; no listening tests or measurements of our own. Detailed human fact-check pending.

Frequently asked questions about the Luxman EQ-500

Does the EQ-500 need an external MC transformer?

No. Two MC transformers for high and low coil impedance are built in. An external transformer can still make sense if it is matched precisely to a particular cartridge.

Can I play 78s with the EQ-500?

Only to a limited extent. The EQ-500 offers the RIAA curve but no alternative curves for shellac or early pressings.

How many turntables can be connected?

Three. Each input can be set on the front to MM, MC High or MC Low.

Is the EQ-500 worth it with just one turntable?

Yes, if the cartridge is high quality and you want to use the adjustment options. With a single turntable and a fixed MM cartridge you mainly pay for flexibility you do not need; a smaller phono stage from the Expert level is then usually the better choice.

How long do the valves need to warm up?

Valve equipment reaches stable operating values only after a few minutes. Luxman gives no fixed time; many owners switch on a quarter of an hour before listening. Valves age with operating hours, so the unit should not be left on permanently.

What is the mono switch for?

With mono records it combines both channels. This reduces noise and distortion from vertical groove movements, which carry no musical information on a mono recording.

Verdict

The Luxman EQ-500 is an all-valve phono stage with built-in MC transformers and unusually extensive front-panel controls. Several reviews describe it as very musical, detailed and expansive, noting that it takes time to set up. In our best list it is the sound champion of the Master level with an index of 92 – a phono stage for listeners with several tonearms who enjoy fine-tuning. Those wanting balanced wiring or a maintenance-free transistor unit will find suitable alternatives at the same level.

Sources